Search:

I could use a 3" coupling and a 3" off the shelf closet flange, but the above (shortened to 4") eliminates one fitting.

I found this one online --http://www.amazon.com/Ez-Flo-40054-Adjustable-Closet-Flange/dp/B005E83NCA
I called the local plumbing supply houses -- didn't get intelligent life forms. All they had was...

I am in need of a PVC "extra long pattern closet flange." I have an Oatey that is 3" (top to bottom), but I need one that is 4" (top to bottom). I see that Law Supply has both a 4" and a 6"...

Will do. Thank you!

Interesting idea, hadn't thought of that.



A check valve would be between the sprinklers and the house, so the pressure drop of the sprinklers should stabilize before the house pressure tank...

I do think that there is plenty of pressure (and capacity) for the sprinklers and the house, it is the inrush when they turn on that creates an abrupt pressure drop, in a few seconds it is back to...

My well is about 400 feet from the house. There are two water lines leaving the well, one goes to the house and sprinklers, the other is only for sprinklers, etc.

I have a CSV and a Welltrox...

It's not the outlet that would be 20 amp, it's the circuit and of course, the 20 amp circuit has #12 wire.

I did get out a multiplier and a surge protector multiplier. You are right the top and...

Just so I understand -- Are the neutrals not connected because of the different amperage of the circuits? I ask this because several of the switch boxes have switches from different 15 amp circuits....

I could put two duplex recepticals -- I presume that I can put them in the same box (yes, I know, connect all neutrals and grounds).

I have added a partition wall in an existing space (next to kitchen). I will be adding one outlet extending the existing 20 amp circuit. Also, I want to have one of these outlets switched with the...

These can be ordered with "Lift and Turn", "PresFlo", or "Push Pull" stoppers.

http://www.terrylove.com/images/watco_flex.jpg

I need the direct drain configuration. It is also available with a more normal configuration.

13991

Any comments regarding WatcoFlex® flexible bath drains.

https://www.buyeagle.biz/WatcoFlex

I have a tight space and one of these would make life a little simpler.
...

I thought it was 6" above the fixture served by the vent.

I absolutely love green copper, but I doubt the wife will like its effect on the white towels.

Thanks for all the responses.

I tend to be cautious about the electric models -- electric heat is simply a controlled short. Also it is a plug in appliance with a life span, I'll eventually end...

I'd like to install a towel warmer. Not the electric type, but plumbed into the hot water line connected to the shower valve. Electric heaters and ones designed for hot water heating systems are...

Thank you for your response.

Alright, #2 toilet will have its own vent. I can either go up to a 90 over connecting to the #1 vent (above toilet bowl level), enclosing this in a new pony wall, OR...

I guess water flows differently from state to state.:)

Amprore -- I am only 27" from the #1 Toilet to the vent, don't think I can get much closer. I thought code was 6'

hj--

Wouldn't the 2" wet vent for the sinks work for toilet #2? Poking around...

Thanks for the response. It certainly makes sense that the #1 vent is not effective if there is water between the toilets. But, would the 3" vent not count, it is less than 6' from the #2 toilet. ...

I poked holes into another area so that I could determine all the venting (and dimensions) for these two bathrooms. Below is an updated drawing (sorry, I've never been able to do 3D drawings). ...

I am doing a bathroom remodel. This is a "guest bath" which consists of a room 5' by 12.5'. The tub and toilet are in a small separate room at the end of the room. It is such a tight little room that...