(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: 311hemi; Keyword(s):

Search: Search took 0.13 seconds.

  1. Replies
    25
    Views
    2,018

    Bringing this back up just to review. ...

    Bringing this back up just to review.

    Currently my system is set to everything I mentioned on the first page. It's a 1.5 cu/ft softener.
    Kcap is currently at: 37000
    Salt/regen:9 (I believe this...
  2. I would require at least 10-12 gmp. One...

    I would require at least 10-12 gmp.

    One detail I left out was that I have a little tannin in my water....if that makes any difference on the setup. Just exploring options at this point.

    If I...
  3. Iron filtration system for irrigation system

    Are there any decent solution for an iron removal system for my yard irrigation, or something that could handle both irrigation and my home system. Currently I am removing iron (3-3.6 ppm) with the...
  4. Replies
    25
    Views
    2,018

    How does one go about this? And thanks, the...

    How does one go about this?

    And thanks, the rest makes sense. Would it hurt anything for me to drop down to 6 lb per ft, from the 9?

    It looks like it would cost around the following for the...
  5. Replies
    25
    Views
    2,018

    Here are the specs from the spec sheet, if that...

    Here are the specs from the spec sheet, if that matters. I have the 150 model.

    20688
  6. Replies
    25
    Views
    2,018

    Compensated hardness = 24 (I set this) K of...

    Compensated hardness = 24 (I set this)
    K of capacity = 37 x 1000
    Salt dose = 9
    Gallons between regens = 1541
    Day override = 5 (I set this)

    Over the past 9 days (since the softener was...
  7. Replies
    25
    Views
    2,018

    The softener came setup from 3M, I assume with...

    The softener came setup from 3M, I assume with their settings in the clack valve. They had set the salt dose at 9. Do I still need to make adjustment to it. Your site says"If you have 2.0 ppm or...
  8. Replies
    25
    Views
    2,018

    Are they correct in that the tannins could foul a...

    Are they correct in that the tannins could foul a iron filter? If so, what would be the recommendation on how to proceed to remove the iron that would not be fouled by tannins. In the long run, I...
  9. Replies
    25
    Views
    2,018

    My hardness listed above is either 7 or 10,...

    My hardness listed above is either 7 or 10, depending one which test you guy by. I calculated using 4 grains per ppm of iron, I seem to see it anywhere from 3-5 depending on who you talk to. I know...
  10. Replies
    25
    Views
    2,018

    Will it be using 3x the salt because I should be...

    Will it be using 3x the salt because I should be regenerating every 4-5 days like I have it set up, so I currently have it running properly? Or, should I let it run at factory settings and remove...
  11. Replies
    25
    Views
    2,018

    It's a model with 1.5 cu/ft fine mesh resin...

    It's a model with 1.5 cu/ft fine mesh resin (manf: 3m Aqua-pure, formerly Cuno), vs the standard model which had the hi-cap resin. I think I only used 600-700 gallons of the 1550 or so it said I had...
  12. Replies
    25
    Views
    2,018

    New water softener programming/setting.

    Hi there, first time poster here but long time viewer.

    I just built a new home and just got the water softener installed along with a inline filter. Everything is plumbed 3/4" Pex, and then has...
Results 1 to 12 of 12