(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: jsarin1; Keyword(s):

Search: Search took 0.12 seconds.

  1. Replies
    13
    Views
    2,682

    Jim, Thanks for the reply. That setup works...

    Jim,

    Thanks for the reply. That setup works perfectly, just what I needed.
    Also it looks like I'm scrapping the crown molding idea and boring my studs instead.

    Thanks again all.
  2. Replies
    13
    Views
    2,682

    Looks like according to code, I need to use metal...

    Looks like according to code, I need to use metal conduit to run the wiring. I can install the conduit behind a crown molding as long as it has 1 1/2 in. from surface of the molding. I'll be doing...
  3. Replies
    13
    Views
    2,682

    Wiring Bathroom Fan

    Can someone explain how to wire a bathroom fan using the wiring from a standard outlet? Attached is a photo of the outlet's wiring.

    17444

    I believe the clump of white wires together is neutral...
  4. Replies
    7
    Views
    1,843

    17388 Took a photo of the lower compartment as...

    17388

    Took a photo of the lower compartment as reference.
  5. Replies
    7
    Views
    1,843

    I have a Honeywell circuit board labeled ST9120C...

    I have a Honeywell circuit board labeled ST9120C 4040. Is this circuit board equivalent to an ignition control module?
  6. Replies
    7
    Views
    1,843

    I forgot to include that the furnace is getting...

    I forgot to include that the furnace is getting electrical power. The blower spins when you turn it on and at the thermostat. According to the thermostat it is calling for heat. I changed the...
  7. Replies
    7
    Views
    1,843

    Furnace will not light

    I have a tempstar furnace with a honeywell smartvalve system. The ignitor will not get red hot to light the furnace.
    I replaced the thermocouple/ignitor with an equivalent one (Honeywell Q3400A1040...
  8. Replies
    11
    Views
    6,439

    Filtering after softening?

    What if the water is cartridge filtered after the softener? Does the filter remove the sodium particles?

    I have a GE cartiridge (...
  9. The turbulator was plugged before I refilled the...

    The turbulator was plugged before I refilled the resin.

    It is an Autotrol 155 unit.

    I unplugged the softener and noticed that in the output port that goes to the house (not from the well) had...
  10. Water Softener On = No Pressure, Bypass = Normal Pressure?

    I just replaced the media in my water softener with a standard resin and amount as suggested by the supplier. After reinstalling the softener I am getting no pressure at all to my house. When I...
  11. I found this on the Delta website:...

    I found this on the Delta website:
    http://www.deltafaucet.com/customersupport/faq/Water+Pressure/

    Is this the process I need to do to flush the water lines?
  12. So I tried to check for the PB problem. When the...

    So I tried to check for the PB problem. When the lever is 100% to on...with both HOT and COLD valves open there the spout drips. With the HOT valve open and COLD valve closed drip continues. With...
  13. HJ thanks for your input again. I'll try to see...

    HJ thanks for your input again. I'll try to see if its a PB problem tomorrow morning as you suggest, I'll post an update soon.
  14. Water!

    I removed the Delta handle kit and reinstalled the test cap. I ran the water and it looks like
    I am getting full water pressure without the cartridge installed. Does this mean that it is
    definetly...
  15. The cartridge was not in the valve when it was...

    The cartridge was not in the valve when it was being soldered. I will remove the trim and try to see if the cartridge is faulty, but I doubt it. I'm guessing that the shut off valves are the...
  16. New tub/shower trim and valve...now tub spout only drips...

    I finally finished sweating the valves and lines together in my bathtub project. Problem now is I'm not getting water! With the valve trim fully open it is only giving me drips out of the tub spout....
  17. I will be using a diverter tub spout...in that...

    I will be using a diverter tub spout...in that case, can you clarify if I should be making any changes to the routing of my lines?

    Also, HJ if you can comment, which of the two diagrams looks ok...
  18. Hj...

    Which of the following will work?

    A) 11566

    or

    B) 11567

    Sorry I wasn't clear on your suggestion...
    I was thinking to add a Female 1/2" Adapter to that open end and just cap it. Thanks for...
  19. Rough Plumbing for Delta multiple shower heads in Tub/Shower?

    I am installing plumbing in my bath to include two showerheads instead of 1. I have attached 2 diagrams of how the lines will be setup. Does this look ok to you guys? Will there be any problems I...
  20. Replies
    4
    Views
    1,368

    I am installing an American Standard tub with an...

    I am installing an American Standard tub with an overflow that's mounted at an angle from the existing plumbing, so I used the flexible coupling for some flex. But, I think I'm going to re-do...
  21. Replies
    4
    Views
    1,368

    Silicone Coulping to PVC Male Adapter?

    I have a tub drain installed to 1.5" PVC Male Adapter via a 1.5" silicone flexible coupling.
    It is tightened down well enough to where it is not leaking. I filled the tub to capacity and allowed it...
Results 1 to 21 of 21