(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: BlackNoir; Keyword(s):

Search: Search took 0.32 seconds.

  1. Replies
    5
    Views
    2,378

    Hmmm.. only 2" eh? I saw a picture of a cabinet...

    Hmmm.. only 2" eh? I saw a picture of a cabinet on a remodel show where they had an opening right under the counter where the put a rolled up towel. It looked really nice but I'm not sure how they...
  2. Replies
    5
    Views
    2,378

    Bathroom Sink with Faucets mounted on the counter.

    Bathroom Sink with Faucets mounted on the counter.
  3. Replies
    5
    Views
    2,378

    Bathroom Sink Positioning

    Not sure this is the best place to ask this but thought I'd try. I'm trying to figure out spacing for a sink so I can build a custom cabinet and I'm not sure what the standard position is for...
  4. Replies
    3
    Views
    708

    I found some how-to's on it. I need a basket...

    I found some how-to's on it. I need a basket Wrench. Thanks again for the info.
  5. Replies
    3
    Views
    708

    Ahh.. that's what my old tub had.. didn't think...

    Ahh.. that's what my old tub had.. didn't think of doing that! How hard is it to remove the bottom drain flange?
  6. Any chance you have a link to one of these?

    Any chance you have a link to one of these?
  7. Replies
    3
    Views
    708

    Tub Drain Question

    Hey all, I have this new tub with the drain lever shown in the picture. Ever time my kids take a bath I worry they're going to get hurt with this thing sticking out like that. Is there any other...
  8. thermostatic temperature control for bathtub

    Hi, I've been googling for this and haven't been lucky. Is there something that I could use to basically dial in a specific temperature of water for a bath? I'm basically looking for something that...
  9. Replies
    2
    Views
    682

    I called them actually and the 'Adjustable' pump...

    I called them actually and the 'Adjustable' pump is an extra option you can opt for when buying the tub. I bought mine off of craigslist so no options for me. They said to upgrade mine at this...
  10. Thread: insulation

    by BlackNoir
    Replies
    1
    Views
    803

    I was just wondering the same thing. Was also...

    I was just wondering the same thing.

    Was also wondering if there was a way to insulate a whirlpool motor so it's not so loud?
  11. Replies
    2
    Views
    682

    Throttling Whirpool Pump

    I bought a whirlpool bath with a 1hp motor and was wondering if there was a way to throttle/slow down the water flow from the pump?

    Thanks,
    BlackNoir
  12. Replies
    22
    Views
    7,183

    Tankless Water Heater for Tub

    I posted this in the Shower & Tub forum before realizing there was a tankless water heater forum so I thought I'd try over here too.


    Is it plausible to get a tankless water heater for a tub? We...
  13. Replies
    0
    Views
    497

    Tankless Water Heater for Tub

    Is it plausible to get a tankless water heater for a tub? We have a 50 gallon water heater and we never seem to have enough hot water for our tub. The tub holds ~90 gallons and it's not like we...
  14. Replies
    2
    Views
    664

    I think I just found the answer. I don't have...

    I think I just found the answer. I don't have the tub yet, going to go look at one tomorrow, but is it common for the drain for the tub to go directly into a horizontal pipe which runs along the...
  15. Replies
    2
    Views
    664

    Question on installing a tub

    I'm putting a drop-in tub in a remodeled bathroom. The drain and water supply lines will be new. The problem is I have no access to directly under the tub once it's in so how do I connect it with...
  16. Replies
    20
    Views
    48,138

    True, they're not actually PEX elbows.. I guess I...

    True, they're not actually PEX elbows.. I guess I was just using them as example. The question still stands, which is, is there any reason not to use PEX elbows?

    But, a good point about the...
  17. Replies
    20
    Views
    48,138

    I'm curious, couldn't you just put in a couple 90...

    I'm curious, couldn't you just put in a couple 90 degree PEX elbows instead of that sharp bend? Is there any reason not to use PEX elbows? Seems like it would be the same as using copper. ...
Results 1 to 17 of 17