(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: SimonT; Keyword(s):

Search: Search took 0.15 seconds.

  1. Did a manual wash in to a bucket to look at water...

    Did a manual wash in to a bucket to look at water and it was pretty clear after 3rd 5Gal I put hose in the drain and then rocked and banged the side of treatment unit. But water was stil clear.
    ...
  2. With the bolt replacing the screw I would guess...

    With the bolt replacing the screw I would guess its full open I now have a GPM of 3.5

    I have done a lot of calling around and I think I found a blue plastic Hydrocharger/ventur for about $60
    ...
  3. Hi LLigeta, I changed out the O ring and...

    Hi LLigeta,

    I changed out the O ring and stopped the leak but then played with the screw and some how busted the screw head clean off, To be able to have the water back on I had to use a normal...
  4. Well I can not seem to undo the union to be able...

    Well I can not seem to undo the union to be able to remove the the Hydrocharger/venturi so I need to go and try and get some pipes to increase leverage to see if that might help.

    but what might be...
  5. Thanks LLigetfa, for all the education I think I...

    Thanks LLigetfa, for all the education I think I might replace the Tee so I can have the draincock off the back of the Tee as there is not much room any where else is it worth putting a pressure...
  6. Hi LLigetfa, Thanks again for all your help, I...

    Hi LLigetfa,
    Thanks again for all your help, I need to go and pickup some larger pipe wrenches as I don't have any thing big enough to get on to the 2 nuts either side of the venturi. Any...
  7. Ok new gauge Installed I used a short stem to...

    Ok new gauge Installed I used a short stem to bring it above the pressure switch so I could see it and wont have to remove the pressure switch if I needed to swap it out again
    ...
  8. So I used the string and icecube method and got...

    So I used the string and icecube method and got it stuck :-( but with some jigging it came up along with some of the fishing line that I lost last time :-) So thank you again for the hint about the...
  9. Thanks for the hint craigpump ,I did just read...

    Thanks for the hint craigpump ,I did just read about some one else dropping a bit of wood down there on string and screwing up there pump and wonder what happened to my lead weight.

    I am trying...
  10. I wanted to also see what it would take to...

    I wanted to also see what it would take to replace the pressure gauge while I was doing the above. I turned off the pump and drained down the water and and had a play with the gauge but looks like I...
  11. ok results are in for pumping rate, I used a...

    ok results are in for pumping rate, I used a shower but removed the shower head it was the closest zone to the pump

    I was able to fill 3.25 Gal in 1 minute before the pump kicked in

    The pump...
  12. About to do the cycle time and and draw down test...

    About to do the cycle time and and draw down test and will then try and do the static water level test but a bit worries after loosing the last bit of fishing line and weight down the well. Will...
  13. I was able to find the well logs attached is a...

    I was able to find the well logs attached is a copy of them 17071

    Data reads as follows

    Static water level is 100ft
    Pump set depth is 320ft
    Well yield is 15.0GPM
    Pump rate is 10.0GPM
    Total...
  14. That recording was listed as a 500 foot well yet...

    That recording was listed as a 500 foot well yet took only about 10 seconds to hit water. Might try a recording my self of the well and use a stop watch. Will do a draw down test tomorrow and make...
  15. LLigetfa its as if you where here as your last...

    LLigetfa its as if you where here as your last post was pretty much spot on.

    Look at the image of the T and then look at it with a light behind it see the red iron oxide in the pipe
    ...
  16. LLigetfa, just wanted to say thanks for your help...

    LLigetfa, just wanted to say thanks for your help so far.

    Yes your right it is a 6" well casing that was one thing I did measure when I opened it up
    ...
  17. With a bit of elbow grease and some leverage I...

    With a bit of elbow grease and some leverage I was able to pop the cap on the well and then remove the broken bolt on the well head.

    But I think I have made a major screw up. I looked down the...
  18. Power for the pump/pressure switch might give a...

    Power for the pump/pressure switch might give a hint to the well pump ? shows 1HP

    http://s9.postimage.org/haz01mqob/IMAG0397.jpg

    Here is the pressure tank...
  19. So any way here is what I have any help in...

    So any way here is what I have any help in identification of any parts to help fill in the above form would be of help, As this morning water was just dribbling out.

    This is where cover to my well...
  20. Please help me document my well and water system

    I was lucky to get a dream home in a foreclosure that had sat empty for nearly 2 years, I think due to its size and issues with leaks in the roofs scared most people off. I have resolved all the roof...
Results 1 to 20 of 20