(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: Tpham2001; Keyword(s):

Search: Search took 0.11 seconds.

  1. If I understand you correctly, my pump is down...

    If I understand you correctly, my pump is down too deep in the well (60 feet or there about). I don't know the water table depth, therefore I'm not comfortable raising the pump to say 35-40 feet...
  2. Hi Valveman, Apologize for the late reply,...

    Hi Valveman,
    Apologize for the late reply, holiday season is crazy here and finally things are slowly getting back to somewhat normal.
    That being said, I relocated the valve to above ground, turn...
  3. Will do, thanks!

    Will do, thanks!
  4. Valveman, The CSV is 18' down. New plan, bring...

    Valveman,
    The CSV is 18' down. New plan, bring the CSV valve up as close as possible to ground level and see what happens.
    Thanks,
    Twin
  5. VAWellDriller, This is somewhat confusing to me...

    VAWellDriller,
    This is somewhat confusing to me and its my first time around the rodeo. When we first pulled the pump, I just start cutting sections as we pulled. So I don't know exactly the length...
  6. Hi All, I did not get a chance to do the...

    Hi All,
    I did not get a chance to do the remaining zones test; but from what I saw the other day, zone 4 with 15 heads for the shrubs were really sad. Some of the heads didn't even have water. I did...
  7. valveman, Yes, I ran same 5 rotating heads...

    valveman,
    Yes, I ran same 5 rotating heads before adding CSV and I got good overlap between the heads. With 20 psi, my overlap decreased more than 1/2.

    This is my set up for each zone.

    zone 1...
  8. VAWellDriller, How do I go about running one...

    VAWellDriller,
    How do I go about running one head with the rest of the heads off? I don't have pump curve, but I think I can google it.

    Thank-you,
    Twin
  9. Hi all, Finally got the motor, csv1w (50 psi);...

    Hi all,
    Finally got the motor, csv1w (50 psi); installed it yesterday. We ran the pump to pressurize the tank to 60 psi. This morning pressure at tank dropped to 50 psi.

    Cut the power to the...
  10. I've asked about 1-1/14" piping in earlier post,...

    I've asked about 1-1/14" piping in earlier post, any thought on Poly vs. PVC?
    Also, if PVC is preferred, can I lower each section into the well and as I go along? As mentioned earlier, the depth of...
  11. Motor is on ordered...

    Motor is on ordered...
  12. But wait, there's more... for $1000.00 I get: ...

    But wait, there's more... for $1000.00 I get:

    -New pump and motor, I asked what brand will he installed; he named myers, goulds, etc...
    -New PVC pipe (4 sections max, I counted the fitting on...
  13. To the best of my knowledge, this is the P&ID for...

    To the best of my knowledge, this is the P&ID for the well system. From cyclestopvalve.com web site, discharge (sprinkler header) should be after the pressure tank? If you look at the first set of...
  14. I replaced PS, flipped the breaker and it tripped...

    I replaced PS, flipped the breaker and it tripped immediate. Called local irrigation guy in the area; he checked everything I've already checked. Pulled the pump and its burnt. I need new pump,...
  15. Thanks, I'll replace it... Also I looked on...

    Thanks, I'll replace it... Also I looked on Well-X-Trol website, their tank is pre-pressurized @ 38 psi, I checked my tank and it read 20 psi; again, is this normal? Do I need to add pressure and...
  16. I checked the continuity from the plug head to...

    I checked the continuity from the plug head to the PS, all wires are fine. I then checked the continuity for the wires going from the PS to the pump and all the wires are fine. While I was at the PS,...
  17. What pump brand do you recommend? Thanks, Twin

    What pump brand do you recommend?

    Thanks,
    Twin
  18. craigpump, thank-you for the response. If I were...

    craigpump, thank-you for the response.
    If I were to remove the pump, I only way I can do this is to cut the 4" PVC casing; the 4 bolts holding the cover plate as you explained are gone. The head on...
  19. Thanks bcpumpguy... Breakers trips, now I know......

    Thanks bcpumpguy... Breakers trips, now I know...
    Now that everything is drying out, I turned the breaker back on; it does not trips. Also, when I plugged in the switch valve nothing seems to be...
  20. Irrigation Well Pump Stop Working After Breaker Jumped - Please Help.

    Hi All,
    My sister bought this house that came complete with well irrigation system; everything works fine until last week. I don't know much about well irrigation system, so please forgive me if I...
Results 1 to 20 of 20