(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: Peter Griffin; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    28
    Views
    4,269

    I think tank exchange is a huge rip off,...

    I think tank exchange is a huge rip off, especially if you have any mechanical skills at all. Might be ok for a little old lady in a wheelchair or someone with more money than common sense though.
  2. Replies
    28
    Views
    4,269

    Be careful of oversizing, overly long peroids...

    Be careful of oversizing, overly long peroids between regenerations are not particularly good for the resin and can lead to channeling of the bed. If you size out at 48 then go with 48. Most...
  3. Replies
    1
    Views
    1,599

    You probably drew the well down pretty far and...

    You probably drew the well down pretty far and that tends to dislodge all that rust on the case. Wait a couple days and see if it clears up
  4. Replies
    28
    Views
    4,269

    Find another thread here with Gary Slussers name...

    Find another thread here with Gary Slussers name and click on his link. It does a pretty good job of explaining how to size your unit. Unfortunately you probably can't get a Clack WS1 online...
  5. Replies
    27
    Views
    5,616

    Zone 6 not well 6, he was referring to sprinkler...

    Zone 6 not well 6, he was referring to sprinkler zones
  6. Replies
    27
    Views
    5,616

    That's a pretty good strategy. Just hang around...

    That's a pretty good strategy. Just hang around and keep an eye on things for awhile if it does indeed pump again.
  7. Replies
    14
    Views
    3,655

    The ENPRESS Vortech™ and Mid-Vortech™...

    The ENPRESS Vortech™ and
    Mid-Vortech™ distribution technologies are revolutionizing the water treatment industry. The design creates fluidity of the media bed and extends contaminant removal...
  8. Replies
    27
    Views
    5,616

    Let's get back on track here. A restriction in...

    Let's get back on track here. A restriction in the discharge line is going to cause the pump to possibly short cycle and I say possibly instead of likely because if you crack your kitchen faucet...
  9. Replies
    14
    Views
    3,655

    The vortex will give you slightly better resin...

    The vortex will give you slightly better resin efficiency but, for all the reasons others have listed above I would go with a gravel underbed.
  10. Wire it right into the pressure switch

    Wire it right into the pressure switch
  11. Replies
    4
    Views
    1,137

    A properly sized softener should do the trick. ...

    A properly sized softener should do the trick. Have your local water fitration company come out and size it for you or you can find a ton of sites online that will give you that information. Water...
  12. Replies
    24
    Views
    4,545

    First off that is a B&G venturi Tee and it is...

    First off that is a B&G venturi Tee and it is properly installed. The venturi tee works on a reduced pressure principal in that an area of low pressure is created at the ventrui that pulls the water...
  13. I assume the hose is on the drain line? and for...

    I assume the hose is on the drain line? and for some reason you can not run a proper drain at this time?
  14. Replies
    25
    Views
    5,740

    Smiling Bob would be proud. got wood?

    Smiling Bob would be proud. got wood?
  15. sure it will work. when you turn either...

    sure it will work. when you turn either thermostat up, both circulators will run. I assume though that that is not your intent so, yes you will need another relay to call the 2nd zone. You can go...
  16. I doubt very much that you have any suction leak...

    I doubt very much that you have any suction leak there, what you had was a classic back flow situation. The check valve has solved your problem. Did you have an approved backflow preventer...
  17. Replies
    30
    Views
    5,588

    This thread is a shining example of how things...

    This thread is a shining example of how things get out of hand. The BLFC only controls flow out of the brine tank in that it establishes the minimal cross sectional area that the brine will flow...
  18. Replies
    6
    Views
    2,809

    Excellent advice Jim

    Excellent advice Jim
  19. Replies
    3
    Views
    587

    "A man's got to know his limitations" Clint...

    "A man's got to know his limitations" Clint Eastwood.
  20. Replies
    5
    Views
    979

    Ahhhh the old Kinetic Water Ram. Fastest way to...

    Ahhhh the old Kinetic Water Ram. Fastest way to make a gawd awful mess that I know of
  21. Bets way to check a gauge is to replace it. A...

    Bets way to check a gauge is to replace it. A new one is like 6 bucks.
  22. It causes the pump to cycle a bit more...

    It causes the pump to cycle a bit more frequently. bump the pressure back up to 2lbs below cut in.
  23. Replies
    309
    Views
    146,137

    I suspect that the purpose of the post was to...

    I suspect that the purpose of the post was to bring the thread back to the first few Google hits.
  24. Replies
    309
    Views
    146,137

    They will never ban a product that does not work

    They will never ban a product that does not work
  25. Replies
    11
    Views
    1,885

    Not trying to beat on you but that's a pretty...

    Not trying to beat on you but that's a pretty complicated job, even for a pro. It will take you a week to cut through that with a sawzall and then getting the necessary fittings back in there is...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4