(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: Spaceball1; Keyword(s):

Search: Search took 0.12 seconds.

  1. So one of these three should work, right? big...

    So one of these three should work, right?

    big orange store...
  2. I thought of putting in a reducer on the...

    I thought of putting in a reducer on the horizontal (that's the trap arm, right?) portion of the pipe, but I wanted to make sure that's up to snuff.

    Also, where (and how) should I switch from PVC...
  3. Sink drain from wall is 2" ABS. What to do?

    I'm putting in a sink for us to use temporarily in the kitchen while I build our cabinets and wait on granite.

    I bought a cheap laundry sink that has a 1-1/2" threaded drain. I also bought 1-1/2"...
  4. Replies
    12
    Views
    2,815

    Upon further review, the existing copper pipe...

    Upon further review, the existing copper pipe uses flared fittings. I'm hiring this part done anyway.
  5. Replies
    12
    Views
    2,815

    Gas line - Converting from dryer to range

    Next up on my remodel..

    Our townhome was set up for an electric range and gas dryer. I'm swapping the two.

    The main gas supply comes in on a 1/2" line to the utility room where the regulator...
  6. Replies
    17
    Views
    2,581

    Well, whatever the case.. I was able to get it...

    Well, whatever the case.. I was able to get it all in. I sweated on a 45 and a 45 street elbow to make an offset. That brought the box forward enough to get the trim plate on. So far, all joints are...
  7. Replies
    17
    Views
    2,581

    Whether for integrity or protecting wires/pipes,...

    Whether for integrity or protecting wires/pipes, the typical installation still goes through the middle of the framing. This box is set up for something different, and there's no indication that it's...
  8. Replies
    17
    Views
    2,581

    I know, I know.. measure twice and all that. ...

    I know, I know.. measure twice and all that.

    It's just frustrating because in some instances you hear how you can only drill through the center section to prevent structural weakness, and you...
  9. Replies
    17
    Views
    2,581

    Yes I did drill the hole before putting the box...

    Yes I did drill the hole before putting the box on the wall, and I don't think that putting the hole in the middle of the sole plate was an unreasonable assumption, either.

    In instances of running...
  10. Replies
    17
    Views
    2,581

    I could be wrong, but to me, that picture looks...

    I could be wrong, but to me, that picture looks like 2x6 framing with the front of the pex about 1" away from the front edge of the sole plate. If the sole plate in the picture were a 2x4, the pex...
  11. Replies
    17
    Views
    2,581

    Icemaker/fridge supply box depth...

    Sometimes I swear that Big Orange (Home Depot) exists just to make my life miserable..

    I'm installing 1/2" copper from a supply line in my lower level utility room to the wall behind my fridge (in...
  12. As it turns out, I was able to find a better...

    As it turns out, I was able to find a better route with no 45's or bends.
  13. Ok to put slight bend in 1/2" hard copper pipe?

    I'm installing a new 1/2" hard copper (blue) line from my utility room to supply water to my fridge.

    Since I'm new at soldering copper, I wanted to figure out a route that would minimize soldered...
  14. I talked the concept over with a pro, and he...

    I talked the concept over with a pro, and he seemed to think that going through the wall would be no problem at all. He also told me that the vent can just live there inside the wall space, so that...
  15. No window above the sink, however, it's a shared...

    No window above the sink, however, it's a shared wall so I'd rather stay out of it if possible.

    I'll have to take a closer look at things, but I'm pretty sure I can go under the floor with no...
  16. Ok, glad I asked. Can I route the new drain...

    Ok, glad I asked.

    Can I route the new drain line under the floor instead of in the wall?

    I'm pretty sure this is a load bearing wall and it's shared with a neighbor, so I'd rather not take the...
  17. Moving kitchen sink, want to get it right..

    We're remodeling the kitchen in our townhome and have removed all of our cabinets. We're working on the design for the new cabinets, and I came across a couple of questions.

    The old sink was in...
Results 1 to 17 of 17