(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: BDrivenByDemons; Keyword(s):

Search: Search took 0.13 seconds.

  1. Replies
    5
    Views
    3,962

    I like this thinking. Manual diverter valves...

    I like this thinking. Manual diverter valves would be perfect for this setup. Now how can I make a diverter valve not close off either section completely? I'm asking to prevent stagnation in either...
  2. Replies
    5
    Views
    3,962

    I had the same thoughts as you but the loops are...

    I had the same thoughts as you but the loops are so small and it's hard to justify placing pumps by my heat source, running 40' of tubing just to get to the space I want to heat, making a small loop,...
  3. Replies
    5
    Views
    3,962

    Open system idea - thoughts?

    I have a 2400 sqft ranch with a full basement. I've been kicking around the idea of putting some radiant pex loops under the bathrooms cause the tile gets so cold. I'm also kind of an efficiency...
  4. Replies
    42
    Views
    3,694

    Are you talking about that model 400 I...

    Are you talking about that model 400 I referenced???
  5. Replies
    42
    Views
    3,694

    that thing looks sweet. seems accurate at a wide...

    that thing looks sweet. seems accurate at a wide range of flow rates. An accurate water test will be critical since the unit seems to be locked to a certain ratio.
  6. Replies
    42
    Views
    3,694

    Routine maintenance is my middle name. That...

    Routine maintenance is my middle name. That doesn't scare me. A unit that works well is what I want. Any suggestions???
  7. Replies
    42
    Views
    3,694

    So this just drops pellets of chlorine down the...

    So this just drops pellets of chlorine down the well - oxidizing the iron - then the iron remover will filter that out plus remove the chlorine by adding the carbon filtration to it? My iron filter...
  8. Replies
    42
    Views
    3,694

    Well damn, I've been reading and reading and...

    Well damn, I've been reading and reading and reading and found this.

    http://www.terrylove.com/forums/showthread.php?41360-Location-of-CSV-and-Aerator-on-Iron-Remover

    I'm starting to think I...
  9. Replies
    42
    Views
    3,694

    Not sure the actual size of the tank but it's...

    Not sure the actual size of the tank but it's labeled as 12.4 gal drawdown @ 40-60PSI. The Model # is SR48-14S-01

    ANybody know a good mail-in water testing place??? I called a few labs around here...
  10. Replies
    42
    Views
    3,694

    So I'm just going to get another analysis done...

    So I'm just going to get another analysis done and post the results here.

    I'm liking the look of my second diagram though. That mixing tank is set to purge at anything over 16" of air in the top....
  11. Replies
    42
    Views
    3,694

    Thanks for the replies, I DID have all my water...

    Thanks for the replies, I DID have all my water testing numbers from when this was first put in but may have misplaced them. If it's really that critical to have them I can get it retested.

    I...
  12. Replies
    42
    Views
    3,694

    Iron Remover/Water Softener redesign

    Take a look and tell me what you think. This my current setup. I put it all in myself when I built my house in 2008. High iron/hardness.

    http://i46.tinypic.com/311qckg.jpg

    I installed this...
  13. Replies
    8
    Views
    4,667

    I have both a bladder tank and a precip tank, the...

    I have both a bladder tank and a precip tank, the air-injector I have can only go in one spot - and that's between the pump and bladder. I don't see how I could ever have water pressure without the...
  14. Replies
    8
    Views
    4,667

    Sorry to bump this old thread but I have the...

    Sorry to bump this old thread but I have the EXACT same setup as the OP and had a few questions.

    The venturi air-injector I use just seems like a piece of junk to me and is constantly getting...
Results 1 to 14 of 14