Search:

Dishwasher disconnect?

You can use the three wire in place of the two wire cable. Don't cut off the third wire. Just leave it long, cap it with a wire nut, and tuck it into the back of the box.

Hi All,
One of our computers just died (kid's computer). The power supply went and I am pretty sure that the motherboard has gone with it. A new psu didn't post so I think the board and or the cpu...

Gary,
I know lots of people drop a post and never return to follow it up but I still enjoy the forums. Even if they don't return I always learn something from other posters such as yourself who take...

I would use rain bird 1800 series with cst nozzles. You install the heads down the center of the lawn strip and the cst's have a square watering pattern. They make various spacing for the cst's. I...

You have a lot of options to look at. There are all types of rotary heads and spray heads. I prefer the Hunter PGP rotary heads for lawn areas. For the flower beds you could use a continuous drip...

If you want to get the box deeper you can either notch the sides of it and it will fit over the lines or you could remove the valve setup and dig the hole deeper. You would need to extend the feed to...

Thanks for the help.

Regarding the box I was thinking of digging out the dirt and putting gravel in there (large gravel so it doesn't get stuck in the heads) which would allow drainage. Is that a bad idea?

That is a...

Yes it is the 1/2 inch brown rain bird drip line. Not sure of the model number of the line I will have to read it when I get home. The emitters have 12" spacing between them. I used a pressure...

I recently added a few zones of Rain Bird drip line to some new flower beds. I think from what I've read that the drip line should be limited to no more than 200 feet on a zone. I brought 1 inch line...

Great I'll use the side inlet so I can bury the head fully without having to mess with the funny/swing pipe.

I bought some 1812 spray heads to replace some 1804's. I need the taller height so I can spray over the top of some flowers in the flower beds. There is a side plug on the 1812's. What is the purpose...

I have an 8 zone system: 6 lawn zones (rotor heads) and 2 garden bed zones along the house (spray heads). I am making flower beds along all of my fence line around the property which will be several...

Use the #10 copper and a 30 amp breaker and you should be fine.

I trust our regular guy so didn't change it. Am I doing the right thing?

So you trust him but you want to check his answer?

The 50 amp breaker is sized to protect the circuit wiring. Most...

That was it. Thanks for the help. They came off easy. Now it doesn't appear to be leaking anymore. What is with that?

I have a Kohler Forte two handle bathroom faucet. I installed this faucet about 5 years ago. One of the handle shutoffs is starting to leak where the handle meets the bonnet. I cannot remember how I...

I have some of these 1800's on my system with vans and there is no problem. As far as debris sometimes I do get very small pebbles in the nozzle. Occasionally I remove the nozzles and clean out the...

Did you run all of your pipe yet? I would use 1" pipe as opposed to 3/4". When you do your permanent connection to the water line in the future then you will need a back flow device like the one...

I try to keep them separate if possible. Sometimes on an older remodel it isn't always easy.

I've seen it done a number of times like this with pipe run up the outside of the house. Personally I don't like it but if it is the only way then sometimes you have no choice. PVC tends to sag with...

Thanks Mick,
I think that I have pretty good head to head coverage. I used good overlap from head to head. I think that I will have to try the cans out there as you suggested and measure what I am...

I have Hunter rotary heads. I installed the system myself about 5 years ago. One of the things that I have always questioned about my nozzle selection was the gallonage output on each individual...

Try something by Arlington....


http://www.arlcatalog.com/Siding/siding.pdf

Most of the stuff is for Vinyl but some of the flat mount types are listed for T-111.