(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: 65Mustang; Keyword(s):

Search: Search took 0.14 seconds.

  1. Replies
    51
    Views
    3,159

    Ok, I believe I have this Fleck 7000 unit working...

    Ok, I believe I have this Fleck 7000 unit working better.

    Yesterday I added 2 gallons of water to the solution to get 1 inch of water sitting on the grid. Added salt to cover the water and let...
  2. Replies
    51
    Views
    3,159

    I found a white sticker on the head. It shows: ...

    I found a white sticker on the head. It shows:

    BLFC = 0.125 GPM
    DLFC Ė GPM

    Also note that when I started the re-gen the other day, there was approximately 4 gallons of water solution in the...
  3. Replies
    51
    Views
    3,159

    Last night, I removed some salt pellets and...

    Last night, I removed some salt pellets and checked the water level in the brine tank. It was just below the plastic ďdeckĒ. I added 1 gallon of water so that the water level was now above the...
  4. Replies
    51
    Views
    3,159

    Looking down the small pipe in the Brine Tank, I...

    Looking down the small pipe in the Brine Tank, I can see water near the bottom. The float is at the bottom. Also, the capacity on the display is at 2050 (never went up). Finally, the hardness...
  5. Replies
    51
    Views
    3,159

    Actually FM is set to t1.2. I did watch the...

    Actually FM is set to t1.2. I did watch the system re-gen at the start. Saw the B1 cycle go 10 minutes with running water throughout, then saw the brine draw begin through the small external...
  6. Replies
    51
    Views
    3,159

    Ok, I ran a re-gen overnight with these settings:...

    Ok, I ran a re-gen overnight with these settings:

    C = 30
    H = 14
    SF= 20
    RC= 150
    DO= 14 (left as 14 days per suggestion)
    B1=10
    BD=60
    B2=5
  7. Replies
    51
    Views
    3,159

    mialynette2003 - Can't seem to find any sticker...

    mialynette2003 - Can't seem to find any sticker indicating Brine Flow Rate.

    All - Any change suggestions to my latest settings ?

    Thanks again for the help.
  8. Replies
    51
    Views
    3,159

    Ok, I think I may be grasping this. Based on...

    Ok, I think I may be grasping this. Based on feedback from all and the sizing chart link, my key settings should be this:

    C = 30
    H = 14
    SF= 20
    RC= 150
    DO= 7 (7 day re-gen based on new BF...
  9. Replies
    51
    Views
    3,159

    Thanks Reach. Iíll see if I can get at the...

    Thanks Reach. Iíll see if I can get at the fitting to take a look at the part.

    Gary; my Bad. I read the Installation Manual incorrectly - it is not 1-for-1 with my head unit. Here is what...
  10. Replies
    51
    Views
    3,159

    Hi all, The tank was loaded with 2 bags of...

    Hi all,

    The tank was loaded with 2 bags of new Morton salt pellets at kick-off in July.
    I emptied out most of the pellets tonight from the plastic bin, I did not see any salt bridge.
    Not...
  11. Replies
    51
    Views
    3,159

    Also looking for Fleck 7000SXT programming advice

    I also am in need of a programming review of my Fleck 7000SXT, 48,000 capacity. I installed it myself, replaced a Northstar all-in-one tank system. Iíve been using the new Fleck about 5 months...
Results 1 to 11 of 11