(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: canton; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.13 seconds.

  1. Utica SSC-100 boiler runs all the time even with thermostat off.

    Hi, Just installed a new wall hung gas-fired hydronic stainless steel condensing boiler with only one zone. After electrician was done wiring boiler, thermostat and co2 detector we tried to fire it...
  2. pedestal

    I usually rough in a pedestal sink drain @ 21", I put my hot and cold supplies 2" above the drain and 4" or 2" off the center of the drain to the left or right according to the faucet spread.
  3. Replies
    2
    Views
    2,547

    Kohler toilet leak at base

    A have a customer that called about a kohler toilet that had a bit of water coming out between the toilet and the floor. He already had 2 plumbers before me, both of them double the wax ring with the...
  4. Victoria and Albert tub, and freestanding faucet/shower valve.

    My g.c's client bought this tub, it's an English manufacturer of high end freestanding and clawfoot tubs. Anyone ever install one of these? I've never installed one of these so it's going to be a...
  5. Replies
    10
    Views
    1,649

    Ma.

    Almost every residential household in Ma. has a 3/4" water supply into the house.
    You want to add a full bath and a laundry, you already have 2 full baths.
    Here's how we size in Ma.
    ...
  6. Thread: Water main

    by canton
    Replies
    1
    Views
    585

    Water main

    I've taken over a job that has 2.5 baths, 1 kitchen and 1 laundrey on each side. The rough plumbing in this gut renovation has already been done and passed inspection. The house has one main that...
  7. Thread: Stack Venting

    by canton
    Replies
    5
    Views
    1,013

    I don't think so.

    In Ma. 3 requirements for Stack venting.
    1.fixtures connect independently into the drain
    2. Are on the same floor
    3.1/4" pitch per ft.
    Maximum distance from trap to vent for the following sizes:...
  8. You are correct sir.

    Actually you can come out from the wall or below the floor.
    Thanks
  9. Kohler K-4854 Bidet- Anyone ever install one of these?

    I have a client that wants to install a new bidet , and this is a newly finished bathroom in a new condo complex, he is closing on the place and would like it done before he moves in. I wondering if...
  10. Replies
    6
    Views
    1,228

    The four seasons are over-rated.

    Stay where you are, you can always have the clams shipped overnight.
  11. Replies
    6
    Views
    1,228

    Yes sir.

    I am. I did look it up in the code book and we need to be 2 ft. above or 10 ft. away. Like I said, there is little alternative other then opening up the walls so I'm gonna ask the inspector what he...
  12. Replies
    6
    Views
    1,228

    Venting question in Ma.

    --------------------------------------------------------------------------------

    My friend has an old house in Gloucester Ma. where the vent for the 1st floor kitchen sink (drum trap) runs out and...
  13. Replies
    3
    Views
    2,396

    Vent problem?

    My friend has an old house in Gloucester Ma. where the vent for the 1st floor kitchen sink (drum trap) runs out and up the side of the house terminating just below the eaves, that is obviously no...
  14. Replies
    57
    Views
    6,855

    Poll: Superbowl winners

    I've personally always liked the underdog. So when the Pats beat the "Greatest show on turf" for their 1st Superbowl victory it was special.
    I live in Ma. and naturally want the Pats to win but it...
  15. Replies
    4
    Views
    1,272

    Vent

    Take the 1 1/2" line from the lav. straight up 6" above the flood level rim of the sink..90 over to the 2" vent and you'll ok as long as you vent that 2" through the roof or tie into another vent in...
  16. Replies
    12
    Views
    7,248

    Massachusetts

    Not allowed here.
  17. Replies
    4
    Views
    3,163

    Standing pilot to electronic ignition

    Is there a kit that converts a standing pilot to electronic ignition?
  18. Replies
    1
    Views
    1,772

    Radiators to baseboard on monoflo system

    This week I had 2 jobs that were basically the same. One had a good outcome the other not so good.
    Customer 1 had 2 cast iron radiators in 2 separate rms. that he wanted taken out and replaced with...
  19. Replies
    3
    Views
    5,431

    Arietta draft hood Dekor glass

    A customer of mine wants a range installed with the above draft hood that is sold exclusively @ HD. He wanted me to quote him an install price without looking at the job. Actually too busy to go out...
  20. Thread: Zone problem.

    by canton
    Replies
    1
    Views
    1,587

    Zone problem.

    My buddy has a single family ranch, he had baseboard heating on 1 zone for the house. He separated the zones so 1 zone would only heat the 3 bedrooms and the other zone would heat the rest of the...
  21. Replies
    3
    Views
    1,374

    Looking for a small tub.

    Who makes a small tub, I have 55" to work with. Anyone?
  22. Replies
    17
    Views
    9,365

    Somerville Ma.

    I'm currently doing a renovation in Somerville Ma., it's the city right next to Cambridge....right up the street from Haaaaavad!
    The plumbing calls for a 1/2 bath on the 1st floor, kitchen sink,...
  23. Replies
    3
    Views
    1,128

    Yeah I pulled it.

    I pulled it and mixed 2 40lb bags of mortar and put that down. It's solid alright, but what a piece of crap neo-angle plastic pan and kit, it's inexpensive at $319 but with all the labor in putting...
  24. Replies
    3
    Views
    1,128

    Neo-Shower Pan....kinda bouncy.

    I just installed a neoshower pan and it gives a little when you stand on it.
    The plastic pan has a ribbed underneath and is pretty solid, the floor that the pan is going on is slightly unlevel so...
  25. Replies
    1
    Views
    837

    Pex..? Should I be worried?

    My client wanted to extend his forced hot water heat into the back bedroom. I usually only use copper but this was tight so this was an ideal situation for the pex tubing. I'm concerned about the...
Results 1 to 25 of 66
Page 1 of 3 1 2 3