(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: Akpsdvan; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.43 seconds.

  1. Replies
    11
    Views
    155

    What kind of salt setting or number of lbs of...

    What kind of salt setting or number of lbs of salt you are trying to use per regen?
    What is the brine flow per minute? .5gpm or .25gpm? there is a sticker on the drain/brine housing on the side of...
  2. Replies
    9
    Views
    84

    Sounds about right as I have only danced with a...

    Sounds about right as I have only danced with a few in this area.
  3. Replies
    9
    Views
    84

    I am trying to remember if the solenoid is an off...

    I am trying to remember if the solenoid is an off the shelf or it is a culligan only, think that it was for the most part off the shelf. But where to find one is going to be the trick.
  4. Replies
    9
    Views
    84

    Thought that the coil for the solenoid was 120 if...

    Thought that the coil for the solenoid was 120 if the rest of the system is 120volt.
    It has been many a year from my last dance with a culligan that had an air pump on it.
    A few months ago I took...
  5. Replies
    9
    Views
    84

    Then the solenoid is to open for the air to get...

    Then the solenoid is to open for the air to get into the tank.
    Solenoid coll could be bad or the guts of the solenoid are bad.
    Have you tested the solenoid to make sure that the coll is energizing?
  6. The normal set up is the GreenSand/pot per unit...

    The normal set up is the GreenSand/pot per unit first and then the softener.

    The Mark 812 most likely would be the pot perm and the Mark 89 is the softener , but that is my best guess.
  7. Replies
    9
    Views
    84

    If you hard wire or jump the pump to run on its...

    If you hard wire or jump the pump to run on its own and it is not pushing air then the pump will need a rebuild.. water is most likely the reason it is not working.
    The relay is more of a timer in...
  8. Thread: Fleck 2850

    by Akpsdvan
    Replies
    4
    Views
    199

    On the large size for a house and the top of the...

    On the large size for a house and the top of the tank will need to be 4" not the 2 1/2 of the 2750.
    Also the 2850 is 1 1/2 in out.. in at the back and out on the side.
    It can be used as softener,...
  9. Replies
    1
    Views
    98

    Might try selling you or the rental company a new...

    Might try selling you or the rental company a new system..
    An injector might be plugged, might be some thing with the piston seal cage.
    Depending on the water quality as to how fast some of those...
  10. Could I hear the question again please?

    Could I hear the question again please?
  11. Replies
    20
    Views
    537

    There is gravel at the bottom of the tank and the...

    There is gravel at the bottom of the tank and the tube will have to be flush..
    Take some 1/2 poly tubing and run one end down the distributor and siphon out the water , then lay the tank on the...
  12. Replies
    20
    Views
    537

    Un do the screws that hold the yoke for the cross...

    Un do the screws that hold the yoke for the cross over tubes, and the screws that hold the meter assembly to the valve and then the valve will un screw from the top of the tank.
    The age of the...
  13. Replies
    20
    Views
    537

    Cordless drill and brush with the handle...

    Cordless drill and brush with the handle removed... been doing that for years , to clean the copper fittings.
    Using it on the brass valve works.

    Some thing tells me that the valve should have had...
  14. Replies
    20
    Views
    537

    I my self would be looking at taking the valve...

    I my self would be looking at taking the valve body off the tank and working on it on a bench.
    Also when the valve body is off the tank one could use maybe some white vinegar to soak the body in to...
  15. Replies
    2
    Views
    179

    It would be good to replace both the upper and...

    It would be good to replace both the upper and lower pistons along with the upper and lower seal pack kits, the lower one has the front half and then the back half when it comes to seals and spacers....
  16. Replies
    2
    Views
    188

    There are a few reasons that it could be doing...

    There are a few reasons that it could be doing what it is doing.
    There could be some thing in the injector assembly area where the piston is at, there is screen around it that could be blocking the...
  17. Replies
    11
    Views
    477

    If it is the meter style, what is the gallons set...

    If it is the meter style, what is the gallons set for?
    What was the iron and hardness level?
    How many people in the home?
    Size of system in max capacity?
    Salt setting?
    Could be that it has been...
  18. Replies
    1
    Views
    158

    Thought that you had that part a part? Clean the...

    Thought that you had that part a part?
    Clean the o ring and the track that it is in and the area where the o ring will be touching.
    If the o ring looks to be in need of replacement then it should...
  19. You might try taking the hot wires from the plug...

    You might try taking the hot wires from the plug and jumping the motor, if it runs then the board is bad, if the motor does not run then the motor is bad.

    Changing the media is not that hard, the...
  20. Replies
    3
    Views
    338

    Sent you a note on book and parts.

    Sent you a note on book and parts.
  21. Replies
    18
    Views
    1,129

    :ohyeah::ohyeah: Good to hear that all is...

    :ohyeah::ohyeah:
    Good to hear that all is returning to normal.
    How did the main piston and its seals look?
  22. Replies
    3
    Views
    338

    The water to drain is most likely the sign that...

    The water to drain is most likely the sign that the main piston and its seal pack are in need of an overhaul.
    The system will need to be in bypass and a cycle started to let the pressure off..
    Now...
  23. Replies
    50
    Views
    2,132

    Both are lasting and are simple to work on. ...

    Both are lasting and are simple to work on.
    Both have valves that have been out for years..
    They are the main stay for a dealer that is NOT of the corp world.
  24. Replies
    50
    Views
    2,132

    If your local culligan dealer has stepped up when...

    If your local culligan dealer has stepped up when there was a challenge and done right and been fair with prices, then there is one choice.
    Another choice would be another dealer in the area that...
  25. Replies
    18
    Views
    1,129

    If there was no screen then I would say it was...

    If there was no screen then I would say it was eaten away.
    Doing a full break down of the system to clean might be some thing that has to be done about every few years.
    You most likely did get the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4