(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: jevonmckinzie; Keyword(s):

Search: Search took 0.11 seconds.

  1. Called electrician

    I called an electrician. I was in a rush to get the heat going and instead of double checking my connections just made a huge mistake. I believe the main breaker might need to be replaced. Anyway,...
  2. Help! New breaker turns off power to other breakers

    Here is my problem. I am installing a 240v electric heater. I ran three wires for the new 40a circuit. At the heater, being dumb, I connected the two hot wires as one to L1 and the neutral white to...
  3. Replies
    4
    Views
    3,792

    Thanks!!! Seems like a much cheaper solution.

    Thanks!!! Seems like a much cheaper solution.
  4. Replies
    4
    Views
    3,792

    Replace Duct vs. Manual Damper

    I am remodeling my home, and I am adding more insulation to the walls and sealing all the air leaks. Basically, some rooms get more air than other rooms. I am wondering if it is possible to install a...
  5. Replies
    19
    Views
    3,079

    Hey, thanks for all the advice and help.

    Hey, thanks for all the advice and help.
  6. Replies
    19
    Views
    3,079

    I realized this wasnt the way to go, but I put it...

    I realized this wasnt the way to go, but I put it out there just to make sure. No luck involved on that one



    I attached an isometric drawing. Tell me if those are S-Traps or P-traps, because I...
  7. Replies
    19
    Views
    3,079

    Wait, how are they S traps. In every diagram I...

    Wait, how are they S traps. In every diagram I have ever seen, the bath and shower P-trap is always two 90s connected like a U and another 90 at the end. If I were to put another 90, then it would be...
  8. Replies
    19
    Views
    3,079

    Sketchup can be a pain at first, but I've started...

    Sketchup can be a pain at first, but I've started to ignore all the little inconsistencies. Plus, its free and I can get more detail than some software that costs over $500.

    I think I've finally...
  9. Replies
    19
    Views
    3,079

    Thanks for the comments. I was wondering if only...

    Thanks for the comments. I was wondering if only the lav vents needed to have the 42" clearance or all vents, either way, quick fix on that.

    I made the vents complex on purpose, but my goal is to...
  10. Replies
    19
    Views
    3,079

    New Master Bath Design

    A month in the making, and I think I am ready to submit my entire remodel plans for a permit to begin work very soon. One of my biggest challenges has been designing the plumbing for the new master...
  11. I guess I wasnt looking hard enough, but I...

    I guess I wasnt looking hard enough, but I finally found a plumbing supply store that sells the M267 for $310.
  12. I knew just going with a pro wouldnt make my life...

    I knew just going with a pro wouldnt make my life any easier. So, I had a plumber come out today and I got the, "I need to figure out a price on this and I'll get back to you", so I know its going to...
  13. I called around for the Zoeller Simplex M267, and...

    I called around for the Zoeller Simplex M267, and so far the range is between $500 - $650, and it costs the same to just get someone to install it so I'm not even going to bother with it, and leave...
  14. From what I can tell, the bathroom downstairs...

    From what I can tell, the bathroom downstairs uses the pump. The rainwater pipes are hidden, and more than likely drain directly into the sewer, but then again I could be wrong.

    As far as pumps...
  15. I measured the copper pipes going into the pump...

    I measured the copper pipes going into the pump and the outside diameter is 7". Does this mean that I need a 3-3.5" PVC pipe to replace the current pipe?

    Catcher_chick, I pulled up the cover...
  16. Thanks. I'm definitely going to tackle this, this...

    Thanks. I'm definitely going to tackle this, this weekend. One more thing, I was looking online to get those Fernco couplings, and only a couple of places have them. Does anyone know any hardware...
  17. Thanks for the reply. I think I got it, seems...

    Thanks for the reply. I think I got it, seems pretty straight forward. Just wondering, why replace the one end of the couplings as PVC??
  18. More Pics

    Just more pictures.
  19. How to replace sewage pump copper pipes???

    I am remodeling my basement. I have a Rigid 1/2 HP sewage pump that is being used for the basement bathroom. Every time it operates, sewer gas comes through and since the furnace is right by it, it...
Results 1 to 19 of 19