(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: jocko11; Keyword(s):

Search: Search took 0.17 seconds.

  1. The valve appears to be a flat cap, there is no...

    The valve appears to be a flat cap, there is no injector on the top, just a block off plate. Filox is a backwash media. I believe the original media was birm, just backwash also. The air injector was...
  2. So i'm going to rebuild the fleck valve and use...

    So i'm going to rebuild the fleck valve and use the old larger tank with the filox. I am ordering another 1/2 cu ft. to make a total 1 1/2 cu ft of media. Is there a benifit to leaving the...
  3. If i use the cabo formula, counting fixtures...

    If i use the cabo formula, counting fixtures downstream of the filter ,i get a service flow rate of 7.2. Filox media specs say it is capable for 6gpm service flow per cu ft. Does that mean you have...
  4. Should I remove the hydro charger, now that I an...

    Should I remove the hydro charger, now that I an using the filox media, or will that enhance the properties of the new media?
  5. The unit with the 12" tank originally came for...

    The unit with the 12" tank originally came for another site, It would foul and need cleaning every five/six months. From the other discussions I suspect the flow was not enough to completely clean...
  6. the cam is white.

    the cam is white.
  7. Should I increase backwash, first group of pins,...

    Should I increase backwash, first group of pins, or rapid rinse, second group of pins? the wheel is black with a white numbered front. What is best time increments for both settings? I have the...
  8. Should I also think about increasing the time of...

    Should I also think about increasing the time of the backwash cycle? It appears that you can do this by adding more pins on the back of the timer.
  9. i ordered two bags of filox media, and a seal and...

    i ordered two bags of filox media, and a seal and piston kit for the fleck 2500. Plan on using the 1 cu tank with that valve. How much head space should there be from top to media?
  10. the iron is well above 3ppm, flow is about 6.5...

    the iron is well above 3ppm, flow is about 6.5 gpm. Does that dictate the smaller tank?
  11. no I didn't take a photo of that. But i belive...

    no I didn't take a photo of that. But i belive that is it, as you described. I will need a rebuild kit for that, and assume the seals and piston are the same as the 2510. I have removed the valve...
  12. the valve on the MacCleens is a brass valve that...

    the valve on the MacCleens is a brass valve that is held on with two screws to the base also brass. Does this base unscrew? If I can use that valve and timer on a different tank, then, how do size...
  13. here are pics

    138541385513856

    these are valve and timers ihave
  14. retrofit a water softner to become an iron filter

    138571385813859Can I retrofit a softner by changing the media and settings on the existing valve? I am replacing a failed MacCleens unit, I also have aquired 3 old softners One 3210 valve and timer,...
  15. retrofit iron filter

    The valves are 3200/ with manual skipper wheel, or 3210/ with water usage auto set wheel. I also have the original 2510 that is on the old MacCleens unit, that could be rebuilt?

    Do you need a...
  16. I don't know how this works so here goes. I have...

    I don't know how this works so here goes. I have a failed MacCleens iron filter that i need to replace. I also have aquired 3 old softners, one with a fleck 3210 and the other 2 with a fleck 3200....
Results 1 to 16 of 16