(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: qpm; Keyword(s):

Search: Search took 0.15 seconds.

  1. Replies
    3
    Views
    1,634

    Perforated PVC Pipe

    Not sure if this the right forum to ask this but thought I'd give it a shot. I discovered a perforated 4-inch PVC pipe sticking vertically out of the ground in a wooded area in the back of my...
  2. Replies
    12
    Views
    8,465

    I already plumbed the softener supply lines down...

    I already plumbed the softener supply lines down in the crawl space and I really don’t have room for it elsewhere anyway. I’m in a somewhat small cabin and want to utilize all the livable space I...
  3. Replies
    6
    Views
    3,074

    Ok, all is working now. Thanks cacher_chick. So...

    Ok, all is working now. Thanks cacher_chick. So the broken cotter pin was part of the problem but also the inlet pipe and the base of the switch were clogged with sediment. I cleaned up and the...
  4. Replies
    12
    Views
    8,465

    The softner is 1.5 cuft. I decided not to go to...

    The softner is 1.5 cuft. I decided not to go to the kitchen sink air gap because it goes to a garbage disposal and worried the salty discharge water will end up rusting the disposal. The kitchen or...
  5. Replies
    6
    Views
    3,074

    Thank you for the information. I took a closer...

    Thank you for the information. I took a closer look at my pressure switch and noticed one of the very small cotter pins had broke off that holds the connectors that press against the red wiring (as...
  6. Replies
    6
    Views
    3,074

    Ok, so there shouldn’t be any pressure reading on...

    Ok, so there shouldn’t be any pressure reading on the gauge when the tank is empty of water, correct? It sounds like I need to adjust my pressure switch to shut off the pump once the water pressure...
  7. Replies
    6
    Views
    3,074

    Well Pressure Tank Problems - HELP!

    I moved my well pressure tank down into my crawl space and now having issues with pressure. The pressure reads zero with the tank empty. It is a bladder style tank so I thought it should read a...
  8. Replies
    17
    Views
    3,894

    Thanks Bob. I probably would have never figured...

    Thanks Bob. I probably would have never figured that out. On the Fleck 5600 it looks like there is an actual salt dose setting on the back of the controller. I thought there might be a similar...
  9. Replies
    17
    Views
    3,894

    The above attached document is the manual I...

    The above attached document is the manual I mentioned having. I do not see anywhere that shows how to set your salt dose or efficiency in the manual. Any help would be greatly appreciated.
  10. Replies
    17
    Views
    3,894

    Fleck 2510 Salt Dose

    Where do you adjust the salt dose on a Fleck 2510? This is the standard model not the digital SE or STX models. It does not mention how to adjust salt setting in the owners manual and I have only...
  11. Replies
    12
    Views
    8,465

    First floor about 4 -5 feet above base of crawl...

    First floor about 4 -5 feet above base of crawl space. Laundary box on second floor, would be about 17 feet from base of crawl or about 13 feet from first floor. The discharge point off softner is...
  12. Replies
    12
    Views
    8,465

    Help with Water Softener Discharge Point

    I am in the process of installing a water softener and trying to figure out a good discharge point for the waste water. I am installing the softener in my crawl space. My laundry area is on the...
Results 1 to 12 of 12