(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: xjmllc; Keyword(s):

Search: Search took 0.10 seconds.

  1. Replies
    6
    Views
    2,112

    The doors are sliding. Not sure about blocking...

    The doors are sliding. Not sure about blocking inside, but i'm sure ill find out when i drill. I guess my main concern is strain on the tub surround over time and the possibility of cracking under...
  2. Replies
    6
    Views
    2,112

    Kohler Shower Door Install question.

    I am installing new kohler shower doors into my existing tub/shower surround. The instructions call for anchoring the side frame to the wall via #8-1.5" screw and anchors. This in fine BUT I must go...
  3. I still have not performed the wiring, but I will...

    I still have not performed the wiring, but I will be THIS week. I will post final results shortly after.

    Again, thanks to all and sorry for the delay.

    xm
  4. Replies
    2
    Views
    1,355

    I'm now almost certain I need to connect the...

    I'm now almost certain I need to connect the pipes (based on the first picture above) it's a supply and return piping through the tank.

    Still, how do I remove this air in the pipes above the...
  5. Thanks for everyone's help. I'll post final...

    Thanks for everyone's help. I'll post final diagram shortly.:D

    xander
  6. Replies
    2
    Views
    1,355

    Air release ? in a converted gravity system

    First off, forgive me if my terminology is off.

    OK, I had an original "gravity" boiler system. The old expansion tank was way up in the attic. The tank/leftover pipes are higher than any radiator....
  7. Replies
    4
    Views
    12,059

    Got 'em !!! Thanks.

    ..and only $.60 cents each!
  8. Replies
    4
    Views
    12,059

    Where can I buy a radiator bleed key?

    I can't seem to find one anywhere, even online. There are a few on ****, but I don't want to wait 5 days for the auction...
  9. Replies
    1
    Views
    3,378

    Filling boiler and system

    My install is about done (with a bit of elec to go). I am now preparing to fill er up. I have:

    Weil CGa boiler
    1 zone,
    Taco 4900 Series Air Seperator on supply side
    Taco 1/8" Hy-Vent on...
  10. OK, so i have both circulators on the single...

    OK, so i have both circulators on the single relay with the TT wires on the relay goin got boiler. I'm still lost as to where/how to wire in the Tekmar 256?

    see:...
  11. So what triggers the SR501 relay to power the 2nd...

    So what triggers the SR501 relay to power the 2nd pump?
  12. Why circulate without heat? Many thanks!

    Why circulate without heat?

    Many thanks!
  13. 1st diagram

    http://www.xjmllc.com/images/wiring.pdfhttp://www.xjmllc.com/images/wiring.pdf
  14. I have 1 zone. Not sure what the circulator...

    I have 1 zone.

    Not sure what the circulator circuit can handle???? How can I find out? Each pump is @ 0.7 amps.

    Where in the schematic do you see where the added controls should be?
  15. Boiler Wiring (Weil CGa, Tekmar 256, Taco SR501, and T-Stat)

    I have:
    new WeilMClain CGa standing pilot boiler.
    two (2) 007 Taco circulators (supply & return sides)
    a Taco Single Zone Switching Relay (SR501) for 2nd circulator
    Tekmar 256 single stage...
  16. Dielectic union between brass and black pipe

    How important is it?

    I'm installing a new boiler with existing black pipe. I will have brass valves (3) and brass taco air separator.

    Are the dielectric unions necessary? Is this a BIG deal?
    ...
  17. Replies
    1
    Views
    3,929

    Dielectic union between brass and black pipe

    How important is it?

    I'm installing a new boiler with existing black pipe. I will have brass valves (3) and brass taco air separator. Are the dielectric unions necessary? Is this a BIG deal?
    ...
Results 1 to 17 of 17