(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: richrc1131; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.13 seconds.

  1. Need help identifying a dishwasher part

    Manufacturer: Kenmore
    Model: 66517052402

    I am installing a used dishwasher that is missing the covers that go over the screws that mount the unit to the cabinets on the right and left sides.
    ...
  2. Replies
    6
    Views
    906

    Found the problem with the light fixture

    I discovered the problem. This device is made up of several segments. Each segment needs to be in physical contact (end to end) with the other. They are loosely joined together by what looks like a 3...
  3. Replies
    6
    Views
    906

    low voltage light question

    I have a ceiling light that has a loose connection between two of the segments. This is one of those low voltage lights.

    What happens is that the light randomly cuts off. If I squeeze that...
  4. found them

    I found them in the screw and fastner aisle. They're called socket head set screws.
  5. Shower handle part identification question

    What is the name of the little screws that are used for securing that cover plate that goes around the shower handle stem covers? They install against the wall.

    The screws are very small, have no...
  6. I guess my main concern is that they said in an...

    I guess my main concern is that they said in an email that they would be drilling for the faucet and handles on site, but they didn't. They just cut a bigger hole.

    I am worried that the bigger...
  7. Ok here are the measurements: counter area: ...

    Ok here are the measurements:

    counter area:
    25" deep (not including back splash area)

    cutout:
    7/8 of an inch clearance from the back splash
    24 1/4" wide
    21 1/14" deep
    2 3/4" from the...
  8. I did supply them with the sink ahead of time.

    I did supply them with the sink ahead of time.
  9. Sink fitting in new granite countertop question

    I hope this is the right thread for this. Sorry if it isn't.

    I just had a granite counter top installed. The contractors for Home Depot I think cut the sink cutout too wide. My wife measured it...
  10. Replies
    1
    Views
    4,466

    Roof cleaning question

    Not sure if this is the right forum or not, but I'm looking for advice on the solution that contractors use to clean moss off roofs. What chemical do they use and how do they apply it?
  11. Replies
    4
    Views
    748

    How to secure a shower rod

    How can I secure a metal shower rod against ceramic tile? What products and/or techniques can I use?
  12. Thread: Weak flush

    by richrc1131
    Replies
    12
    Views
    1,781

    @jadnashua - It hasn't always been this way. In...

    @jadnashua - It hasn't always been this way. In fact, it's been difficult to figure out a pattern to this issue. It's been happening for a while. After talking with my wife about this, we think that...
  13. Thread: Weak flush

    by richrc1131
    Replies
    12
    Views
    1,781

    Weak flush

    I need some advice.

    A toilet in our half bath has a weak flush. We've snaked the toilet (nothing). Removed the toilet and snaked the line (nothing). Still a weak flush. What other troubleshooting...
  14. Actually, we're going to take our time (we're...

    Actually, we're going to take our time (we're novices) and even remove the sub floor (it has water damage). I want to do this in as standard a way as possible. I'm having someone relocate the supply...
  15. We're going to be pulling up the entire floor,...

    We're going to be pulling up the entire floor, pulling down two walls that weren't insulated, and installing a new sink.
  16. This just doesn't look right. What do you think?

    My wife and I are finally getting around to the demo on a half bath on the first floor. Wifey disconnected and drained the current toilet while I was at work and sent me this pic.

    Her ex...
  17. Thanks for the great advice. I will jump on...

    Thanks for the great advice. I will jump on sealing off the little leaks at the very bottom of the walls first.
  18. I'm looking to insulate the bottom floor of my...

    I'm looking to insulate the bottom floor of my house which is the ceiling in the basement. I'm tired of cold floors.
  19. Floor insulation question from a newbie

    I'm planning on insulating the bottom floor of my house soon due to very cold floors and while I've checked out the steps necessary to do this, I still have a question:

    (Preface) - My basement...
  20. Replies
    7
    Views
    4,543

    Finished wall needs insulation

    I need to insulate a finished wall (first floor). The inside of the wall is covered by cabinets.

    I cut a hole in the wall because it was always cold and found that there was no insulation.

    I...
  21. Replies
    3
    Views
    1,219

    Now that you mention it, although I did swap the...

    Now that you mention it, although I did swap the handles, I used the same screw. That may be it. I will also look into getting better handles.
    Newbie question here: Does the brand of handle have to...
  22. Replies
    3
    Views
    1,219

    Shower handles

    The cold water shower handle for some reason keeps coming loose. I've replaced it, but it keeps coming loose on that side. I thought that maybe the grooves on the valve stem were worn, but they don't...
  23. Replies
    1
    Views
    1,504

    Baseboard heater cover height question

    In trying to finish off my wife's ex's work in the house, I discovered that he installed electrical outlets too low above the baseboard heater piping.

    I went to install standard size heater...
  24. Replies
    1
    Views
    884

    Leaking cold water valve

    The cold water valve to the sink in our half bath is leaking ever so slightly. It's not leaking at the handle or at the connection to the cold water handle. It's leaking at the connection point to...
  25. Replies
    4
    Views
    1,165

    Sounds good, but I couldn't find a supplier of...

    Sounds good, but I couldn't find a supplier of Rescue Tape in my area. I live in Central Connecticut.
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4