(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: weneedhelp; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.11 seconds.

  1. I am still here along with Issue. It has been...

    I am still here along with Issue.
    It has been very hot in the Phoenix area and I have not yet decided how to continue.
    But, i will post another picture with more details about what I tried to do...
  2. Well everything came apart and I changed the two...

    Well everything came apart and I changed the two Nipples and behold I had another problem.
    I had to extend one end 1/4-3/16 to fit flush against the Copper Union Coupling and it leaks at the...
  3. Everything you said is true. When the Setup was...

    Everything you said is true.
    When the Setup was changed, the male copper solder 1" were removed from both ends of canister head.
    It was replaced with 1" female copper fitting and sch 80 1"...
  4. What ever its called, i have one opened on the...

    What ever its called, i have one opened on the outlet side of the filter and the inlet side's union is the one that is difficult.

    I did use Pipe Wrenchs (old type,red) they held it steady, but i...
  5. 13260 It is a Compression coupling. I was...

    13260

    It is a Compression coupling.

    I was able to loosen one end.
    was unable to attach/insert picture, but will keep trying.

    hope it worked.
  6. 1" Copper Union..Stuck Cannot Loosen to Remove?

    Have the copper union on either side of a whole house filter before it goes into the Water Softener. Before it gets to the Union, the main water line goes thru a bipass installed by pro. I need to...
  7. Replies
    4
    Views
    1,747

    fixed

    Fixed used a round file to clean instide of brass tube. thanks
    Sey
  8. Replies
    4
    Views
    1,747

    i think i will just call in the morning. it...

    i think i will just call in the morning.
    it gets caught at the bottom of the brass tube. 32298 grohe.
  9. Replies
    4
    Views
    1,747

    Attach SS Sink to new Granite Countertop

    I have a 22/33 overmount that I have set into my 33" Sink Cabinet.

    Just had new granite top installed and would like to attach sink using a Adhesive as i had done in previous installation.
    ...
  10. Solder Ball Valves(3) Confused about Open/Close and Where to Heat?

    Several questions which i would like resolved.

    1. Solder Method Open or Closed?
    2. Where to Place Heat on Brass or Pipe?
    3. Will Propane do or should i use Mapp?

    This is for a Bypass...
  11. Replies
    6
    Views
    1,056

    I give up!

    I GIVE UP!

    Will try to find a Plumber to finish Installation.

    Thanks for the replies.

    Sey
  12. Replies
    6
    Views
    1,056

    For me i think that i have to dry/fit the tub. ...

    For me i think that i have to dry/fit the tub. But will stop if it becomes a tremendous problem.
    comments appreciated.

    thanks.
    sey
  13. Replies
    6
    Views
    1,056

    Thanks, as always. Would you use the Kohler...

    Thanks, as always.
    Would you use the Kohler drawings or Measure tub?

    The picture attached is where I am now.

    When I cut the pipe from inside I left about 5/8" of the Tee on the Pipe.
    My...
  14. Replies
    6
    Views
    1,056

    I did plan on cutting below the tee. My next...

    I did plan on cutting below the tee.

    My next step is to dry fit the tub to get exact locations.

    Th anks for you help,
    Are you in the Phoenix Area?
  15. Replies
    6
    Views
    1,056

    New Tub Drain/Ovfl transition Old Trap

    Before I break the concrete arount the Tee and Trap, would like to have the Connections that I would need to transition from the 1 1/2" od white sch 40 to my trap which is black sch 40 2"?

    The...
  16. I got the answers to my inquiry, so I am ok, and...

    I got the answers to my inquiry, so I am ok, and will buy a lot of elbows.

    Next question is:

    Is it possible to plumb the supply lines to and from the valve before the
    Tub is installed?
    ...
  17. Replies
    4
    Views
    529

    thanks, I needed that. Sey

    thanks, I needed that.

    Sey
  18. Replies
    4
    Views
    529

    I cannot find the Delete Icon?

    I cannot find the Delete Icon?
  19. Replies
    4
    Views
    529

    How do I change/edit thread name??????

    see above thread name
  20. What is the correct way to layout the pipe for the Soiree TKS960M set?

    What is the correct way to layout the pipe for the Soiree TKS960M set?

    I am building a solid frame(2x6) to hold the very heavy brass fixtures.
    Water Supply Lines are just below the Top of the...
  21. Replies
    5
    Views
    1,698

    I am already laying out the install plan and will...

    I am already laying out the install plan and will let you know when it is complete. Thanks for all your ideas, i will use them as soon as i nail down the tub exact detail location.

    Sey
  22. Replies
    5
    Views
    1,698

    thanks, do you have any idea about how high or...

    thanks,
    do you have any idea about how high or the slant angle???
    For the Grab Bar.

    sey
  23. Replies
    5
    Views
    1,698

    Alcove Tub Install (misc)

    We are planning to install a 24" Soiree Grab Bar on the Right Side of the alcove in the tub area. We need maximum strength because we are not young and need help getting in and out of the tub. ...
  24. I am in contact with them and they think they...

    I am in contact with them and they think they have a drain that will work.
    Just hope they are right.
    Sometimes everyone makes mistakes. Just have to correct it.

    Thanks
    Sey
  25. Vessel Sink 2" Drain Opening, Need Drain?

    I have a Porcher Sink that was shipped to me from a company that went out of business and now I fine that it has the European Sized Opening.
    My Sink is an Overflow Sink, and my Hardware is Toto...
Results 1 to 25 of 61
Page 1 of 3 1 2 3