Search:

How is it determined where a circuits first receptacle is,for GFCI protection to all other receptacles downstream on that circuit? If this helps... 9 of the 13 receptacles have a single 2 wire cable...

Thanks all for the great replys much appreciated!
Speedy i knew what you meant about crawl space and crazy..lol. just joking about no malice meant.
BobNH i had a fairly easy time pulling #10...

Thanks for the reply Jimbo..Sounds great! Yep, the motion sensor light will be the only thing on the circuit.

I would like to install a motion light. It is 750 watts total (each of the three lights 250 watts) In the place i want to install the fixture, has existing 14/2 that goes to a 15 amp breaker. At the...

Thanks all for your replys.

Can someone please decipher what RAB is... (brand,acronym etc.)

I did not know my question and concerns were considered crazy...lol re: routing of protected 10/2...

I want to put a washer/dryer in a kitchen which will require moving the hot water heater,and running a longer 10/2 protected with FMC from the breaker panel to the hot water heater. Behind the washer...

It comes in 10' sections and uses a PVC coupler to add to the length needed.
Of course it is rated for potable and drinking water as confimed via the company and labeled on each pipe. I have heard...

Hi Day425, No advice or help here ,but I maybe am having a similar problem to yours,but single level home here. The house was built in 1957,so it still has the galvanized pipe water main. I wrote in...

The other area video scoped was the section of water main that runs under the slab to where the main threads into the run to the water meter by the curb. The under the slab run checked out clear as...

My hose bib outside in the back reads @ 70-75 psi when the bib is turned on full with nothing on.When i turn on a sink on ,or flush the 1.6 gallon toilet the pressure drops to 20 psi, and it takes...

Is this only effecting this model HWH, or other electric or gas models too?

The location of a GFCI brings up a thought for me in general. At my friends house they had some mega remodel work done a while ago. Contractor,sub for this sub for that and all... Their job was just...

This thick heavy gauge bare copper wire runs from the inside of my breaker panel down through the inside of a framed wall perhaps into the earth.....(some nearby work with sheet rock allowed me to...

Thanks for the reply Dallas and jimbo.

I did try with the pressure relief valve tipped and all hot water taps open in the bathroom and kitchen what is left yet to open is the tub/shower hot...

I went to go drain my hot water heater... Craftmaster,30 gal. , double element. Turned off the breaker to HWH,turned off the water supply,opened up the hot water side on a faucet,hooked a short hose...

Are there any problems with making a 10/2 cable longer than it has to be,for future plans that will require the moving of an appliance? In this case @ 3 or 4 feet longer ,so when that appliance is...

After cutting the flexible conduit to length then putting the wire to be used in it - Is there not something they make that protects the wire from that raw cut edge of the conduit..? (a protective...

I am around projects i have done almost everyday,and have used either of connections you speak of ,and have noticed no problems to date. My main critera either pre twisted or not is that the wire nut...

As per a previous thread i started re: re wireing

Actually it should be grounding a un grounded house short of a complete re wire... Anyway what i mean by confusion is this..I have talked to...

Thank you for your reply jdoll42 just got it now 10:09PM EST. Oh yah before i make a move whether it be a diy or an electrician i will check with the codes that are applicable to this state ,and...

Thanks so much for the reply Bob NH! Seems i picked an unpopular subject to ask about...lol only one reply...lol Anyway more questions i have as you perhaps might have imagined..

I like the idea...

Tomorrow i will start getting estimates for a re wire of this house that was built in the late 50's.Just wanted to get some prior knowledge and heads up from here prior to those estimates.. The wire...