(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: bbillcee; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.46 seconds.

  1. Replies
    1
    Views
    521

    piping for flushometer???

    Hi

    my house was bulit in 1935, i originally had 2 flushometers, 1 on 1st floor and 1 on 2nd floor.

    they both were fed from the same 1 inch riser that went up the wet wall

    the 2nd floor was...
  2. they have gaskets......maybe i'll just leave it...

    they have gaskets......maybe i'll just leave it as is for now and see if i experience any movement with everyday use
  3. tightening widespread valve bodies on granite

    hi

    i tightened down some valves on the granite vanity top, i made them pretty tight, but if try to move them they can move though it takes some forcing

    how tight can i make them on granite? ...
  4. Replies
    7
    Views
    1,288

    thanx hj, one of the nipples is 2" what is...

    thanx hj, one of the nipples is 2" what is the best way to bring down to 1.5 inch? just a reducer coupling with a 1.5 nipple then the desanko? also can the desanko be used to transition to a PVC...
  5. Replies
    7
    Views
    1,288

    connecting trap to galvanized nipples

    can u use a pvc trap and slip nut just like u would a brass tubular when connecting to a galvanized nipple?

    over the years i always find the gal rots where connecting to the brass
  6. what are some tricks to tighten chrome/nickel etc pipes

    i see some guys use a pipe wrench close to the wall behind finish plates, duct tape around the pipe, what do u pro's do?
  7. Replies
    3
    Views
    849

    hehe i am electrician and we thread and bend ...

    hehe i am electrician and we thread and bend thick walled aluminum pipe so i figured what the hey!

    anyway i found a satin nickel one for like 40 bucks shipped thanx for input
  8. Replies
    3
    Views
    849

    aluminum pipe for water?

    can i use threaded aluminum pipe for say a 12 inch piece of pipe to the shower head?

    the standard 8 in 45 degree they give u is shooting the water out of the tub so i wanted to make a sharper...
  9. Replies
    6
    Views
    1,664

    who usually installs the tub? the plumber or...

    who usually installs the tub? the plumber or carpenter?
  10. Replies
    6
    Views
    1,664

    how to level an EXISTING cast iron tub

    we have gutted the bathroom ( we are having the tub reglazed) and the ledger board that the cast iron tub rests on seems to be rotted out, i dont want to remove the tub because a mud job was put in...
  11. Replies
    4
    Views
    604

    yes its brass .....what did they put on the...

    yes its brass .....what did they put on the threads besides the string in them dayz
  12. Replies
    4
    Views
    604

    starting 2nd floor renovations

    2 questions for you guys

    1- I am thinking of tiling over the original floor in the bathroom......it would be a real bitch take out i know the cement is around 4-5 inches so would rather just...
  13. Replies
    2
    Views
    1,666

    thanks HJ i just though maybe the 2 inch would...

    thanks HJ i just though maybe the 2 inch would having things flowing better...the 2 gal i replaced was down to about 3/4 with all the build up:eek:
  14. Replies
    2
    Views
    1,666

    2 inch vs 1.5 trap for kitchen sink

    i have a 2 inch pvc 90 stubbed out under the sink....i was planning to install a 2 inch trap then use a 2 in to 1,5 reducer to connect to the tail piece

    or would it be better to put an a 2 inch...
  15. Replies
    5
    Views
    813

    thanx all....getting the granite in...

    thanx all....getting the granite in tomorrow...hell of time for this to happen
  16. Replies
    5
    Views
    813

    emergency advice fast

    i had to pull out new kitchen cabinet for get at an old galvanized waste that failed....i got the galvanized nipple out of the threaded cast fitting and need to know if a male pvc adapter is...
  17. i dunno.....i messed with this old pipe before...

    i dunno.....i messed with this old pipe before and snapped some.....the last thing i wanna do is snap some and have to start ripping this wall down
  18. thank u for reply..its brass pipe

    thank u for reply..its brass pipe
  19. some input on removing old nipples or not?

    i will be replacing the wall mount faucet in the kitchen....i was originally gonna do tiles or granite for the back splash now i'm just gonna do a 3 inch back splash and plaster and paint over the...
  20. Replies
    7
    Views
    1,348

    hahah the house is made well......as i am...

    hahah

    the house is made well......as i am beginning to see with everything.......older is better but yet we are all brainwashed that the new crap is better.......this goes for cars, audio...
  21. Replies
    7
    Views
    1,348

    thanx just needed some reassurance!

    thanx just needed some reassurance!
  22. Replies
    7
    Views
    1,348

    anymore input on this? thanks tom!

    anymore input on this?

    thanks tom!
  23. Replies
    7
    Views
    1,348

    old brass pipe

    my house has brass threaded pipe through out ...i'm remodeling the kitchen and am gonna keep the wall mounted kitchen faucet just gonne get a new one

    my question is the should i change out the old...
  24. Replies
    4
    Views
    1,113

    ok thanx mang

    ok thanx mang
  25. Replies
    4
    Views
    1,113

    gas valve next to electical outlet?

    i have a gas valve a couple inches away from a electrical outlet for the stove....is this normally against code? i'm in NY
Results 1 to 25 of 101
Page 1 of 5 1 2 3 4