(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: Fastclient; Keyword(s):

Search: Search took 0.11 seconds.

  1. Replies
    14
    Views
    773

    Thanks Terry, can you give me an idea of how big...

    Thanks Terry, can you give me an idea of how big the piles should be. Don't want to put down some mortar, set the tub in it then remove the tub because there is too much mortar and I have to remove...
  2. Replies
    14
    Views
    773

    Any help or suggestions on how much mortar under...

    Any help or suggestions on how much mortar under the tub? Would really appreciate some insight on this Thanks!
  3. Replies
    14
    Views
    773

    Thanks guys for all the info, greatly...

    Thanks guys for all the info, greatly appreciated. I plan on setting the tub in mortar. The tub has a waffle type bottom so this should work well. I read in another thread how it would be almost...
  4. Replies
    14
    Views
    773

    Where the overflow attaches to the tub is angled....

    Where the overflow attaches to the tub is angled. Would a standard off the shelf overflow kit adjust to this angle of the tub?
  5. Replies
    14
    Views
    773

    Thanks for the quick reply. Another question...

    Thanks for the quick reply. Another question about the tub. American Standard suggest drain kit 1545.170 for the Princeton tub. It is a lift and turn drain that costs about $120. The front of the...
  6. Replies
    14
    Views
    773

    American Standard Princeton Install

    I am installing a American Standard Princeton bathtub. I removed underlayment floor in the bathroom down to the subfloor. Unfortunately the subfloor is only 1/2" thick. Also the floor joists run the...
  7. Replies
    6
    Views
    5,145

    Do you know how many posts there are if you do a...

    Do you know how many posts there are if you do a search on wax rings?? Me neither but there are LOTS! So I will just ask the question hoping for a quick answer. When setting the toliet do you put...
  8. Replies
    6
    Views
    5,145

    2 Wax rings or extenders?

    Found some situations close to mine with answers but nothing quite the same. Neighbor installed a new ceramic floor and with the cement board and tile the flange was down quite a bit but two extender...
  9. Replies
    1
    Views
    633

    Toilet flange extension

    I have searched and searched for an answer and I must be wording my search wrong for I can't find a definitive answer. I tiled my bathroom floor and now the flnge is below floor level. I plan on...
  10. Replies
    5
    Views
    21,521

    Swanstone Shower pan

    I too am installing the Swanstone shower pan and was going to embed it in the recommended bed of "Quickrete" mortar mix. Since you posted this a while back and even tho no one replied to your...
  11. Replies
    5
    Views
    2,644

    Distance is a factor

    Have to agree with HJ. The trim ring (escutcheon) is huge on this Delta faucet, about the size of a garbage can cover (actually it's 7.5") so distance between the trim ring and spout is a factor. ...
  12. Replies
    5
    Views
    2,644

    Works fine!!

    Finished the job and with ony 5 inches between the valve and spout (6.5 inches if measured between the center of the valve and center of spout outlet) everything works great. No backfeed up to the...
  13. Replies
    5
    Views
    2,644

    Distance between valve and spout

    I am installing a Delta 1748 and the instructions say there is to be a minimum of 8" with a max of 18" between the valve and the spout nipple. I am replacing an existing setup and the holes are...
Results 1 to 13 of 13