(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: JoeT; Keyword(s):

Search: Search took 0.14 seconds.

  1. Thread: Flange and tiling

    by JoeT
    Replies
    2
    Views
    452

    Thanks Gary, The plumber left me enough...

    Thanks Gary, The plumber left me enough flexibility to set the flange on top of the tile.
  2. Thread: Flange and tiling

    by JoeT
    Replies
    2
    Views
    452

    Flange and tiling

    Hello all, I'm a newby, I searched the FAQs but didn't find an answer to this. My plumber roughed in a toilet flange for me a while ago. I'm now to the tile stage, my question is should the flange be...
  3. Thread: Toilet move

    by JoeT
    Replies
    3
    Views
    831

    thanks guys.

    thanks guys.
  4. Replies
    6
    Views
    3,096

    never mind....I found the answer.....helps to...

    never mind....I found the answer.....helps to search first....thanks folks
  5. Replies
    6
    Views
    3,096

    remove a shark bite

    Hi folks, is there a way to remove a shark bite coupler from a copper pipe?
  6. Thread: Toilet move

    by JoeT
    Replies
    3
    Views
    831

    Toilet move

    Hi, My plumber roughed in my toilet piping before I completed the space due to a scheduling conflict. The problem I have is that I'm an inch and a half off of center of the toilet stall. I can access...
  7. Thread: newbie

    by JoeT
    Replies
    21
    Views
    2,582

    Shower head

    Ok...I have more plumbing questions. I ordered a Symmons BP-46-2X temptrol valve, which should be delivered today. I haven't ordered a shower head yet though. I'm leaning towards a 6 or 8 inch rain...
  8. Thread: newbie

    by JoeT
    Replies
    21
    Views
    2,582

    Thanks to all for your advice. It's greatly...

    Thanks to all for your advice. It's greatly appreciated. Quag, that is my plan exactly.... solder everything then sharkbite to the pex.....I'm putting an access panel in the room next to the...
  9. Thread: newbie

    by JoeT
    Replies
    21
    Views
    2,582

    Hi Jim, Thanks for the advice. I think I bumped...

    Hi Jim, Thanks for the advice. I think I bumped into you on the JB forum also.
  10. Thread: newbie

    by JoeT
    Replies
    21
    Views
    2,582

    Thanks again! Any good sources on line for shower...

    Thanks again! Any good sources on line for shower parts? I'm looking for a basic 2 handle rough in valve. My big boxes don't have very much of a choice...and plumbing supplies are closed by the time...
  11. Thread: newbie

    by JoeT
    Replies
    21
    Views
    2,582

    Thanks Redwood. This is just a shower so it'll be...

    Thanks Redwood. This is just a shower so it'll be just to the mixing valve. Is there something I could use to cut the pex beside a pex cutter? If I could cut a level, flat line, with a utility...
  12. Thread: newbie

    by JoeT
    Replies
    21
    Views
    2,582

    Thanks Redwood, that's what I'm looking for. Do...

    Thanks Redwood, that's what I'm looking for. Do you know if these are available at the big box places, or should I hit a plumbing supply? Gary, thanks for the input, and I see your point, but it...
  13. Thread: newbie

    by JoeT
    Replies
    21
    Views
    2,582

    Redwood, no I don't have any pex tools....and...

    Redwood, no I don't have any pex tools....and yes, I can sweat copper. HJ I'm new here, so I don't know if I can post a picture yet. The plumber roughed in a sink, shower and toilet valve from my...
  14. Thread: newbie

    by JoeT
    Replies
    21
    Views
    2,582

    newbie

    Hi, I'm new to the forum. I have a question that may have been asked hundreds of times....I did search. My plumber roughed in my new bathroom with pex. I have no idea what type of connectors to use....
Results 1 to 14 of 14