Search:

Thanks! I was hoping the answer was that easy

bump

Any help on this one?

Hey Guys,
I'm hoping this is the right forum for this, but we have a pretty big backyard organic garden. Our rain barrels are far enough away that I need additional pressure to be able to water the...

Big2bird,
can i ask a follow up question:
in the picture below, the clip on the right is the 13/14 (co-joined) and the one on the left, as marked is the blk8.

Can I simply push the wire from...

thanks for your help big2bird

Thanks for the reply. I did validate it is rated for 'line voltage':
The H46C Humidity Controller is used with portable and
central unit dehumidifiers to maintain relative humidity.
The H46...

Hello,

I need some help wiring my humidistat to the dehumidifier.

I'm using the H46C from Honeywell, and I have a Santa Fe Impact dehumidifier. The humidistat is in the basement finished room...

Hey guys,
I need a bit of help understanding a diagram. I want to hard wire my 240 circuit to a timer, then wire the outlet from the timer, I don't want to assume with this one :)

I'm hoping the...

so is there a trick to the tapcon pre-drill? because the drill bit they gave me lasted about 5 holes and now it's completely useless, i can't drill any further than 1/2" into the concrete and the...

on my first floor, i pretty much cut 6" slats of plywood spaced them 3/4" apart and used a router to make arches in the plywood so they weren't really sleepers, it was essentially custom routed...

Ok, great, thanks for all the advice I appreciate it, I took the week off to get started and it's wednesday already and I haven't done ANYthing!

i'm anxious to get started!

Thanks Dana,

I have some R13, and R21 cotton batting left over from the first floor, so the R21 can definitely be split by depth.

I will be installing hydronic radiant heat (an extension of my...

the only moisture trouble I have experienced was two fold, a chimney that I ripped out: Problem Solved and my basement door/walk out...but that was during the 2008 '100 years rain' we had here in...

Thanks for the reply!

I was taking some measurements tonight, and that chamfered edge isn't present in all circumstances, to be honest this whole house is just 'a little bit off' in every...

Thanks John, I read a PDF from the John Bridge tile forum that talks about using cork or foam and they seem somewhat close in their heat loss prevention properties.

You're right, there must be...

Hey guys hoping someone might have insight into tiling over xps rigid foam board? Part of my basement remodel i would like to tile most of the basement. Right now its just a slab below grade, so i...

OK! Thanks for all that information, I've read it about 6 times now, and I'm hoping I'm getting the gist of it. I think you're what you're saying isn't too far off from my original plan.

For...

Thanks for the reply, I was toying with that idea, but I saw a few videos mention the XPS AS the vapor barrier, and taping all the seams for full coverage.

I like your idea, i'm just concerned I...

Hey everyone, you were a big help during my 1st floor renovation, I even had Terry's crew come install the Aquia 2 dual flush with soft close seat in the new bathroom, it's a great fixture!

I took...

Hey guys, I've found conflicting advice about ABS and it's UV resistance, and I have a situation where my kitchen drain goes into my basement (which I can access) and out through the house wall just...

Hey guys, I'm having a hell of a time trying to find a decent range hood that i can vent through the wall, that does NOT have to be mounted to a cabinet...

most of the ikea/HD ones don't...

Hey guys, I'm building a medicine cabinet and I've created it so the door is flush with the face.

To do this I used a rabbited edge on the sides of the cabinet. I'm looking for a hinge that is...

Dana,
Thanks for the reply! It is in fact in Seattle, and it gets a bit trickier as this ceiling is the basement ceiling (i.e. underneath the subfloor). And my joist spacing is 6x6's on 36"...

I'm wondering if anyone knows what the name of the product is that I see in most insulation pictures where batts are put overhead?

It looks like a plastic sheet, but I'm pretty sure it's adhesive,...

Hey guys, long time no talk, spent the summer overhauling the yard, now I"m back to the kitchen, got my cabinets, and countertops ready to go, i'm trying to decide on sinks/faucets...


Does...