alternety
Like an engineer

Gerber also makes a wall hung toilet. We do a lot of Glenwall installs too.

I have never looked into a wall to see if a shower arm was leaking. Either put tape on the threads, or pipe dope, thread the head onto the arm by...

With 11.5" to the wall you're fine with either the 500 or the Vespin II with their standard 12" kits.

I've installed the Neorest 500 at 11.5" from the back wall. Are you measuring the wall? Or the floor mold? You can also fudge the adaper...

That works with the 2" veritcal pipe on the vent.

It's just a matter of picking up a roof flashing, and putting the holes in the right location to drop a pipe through. It's not a lot in parts. In...

It drives the plumbing inspectors nuts that Home Depot sells product that doesn't meet plumbing codes. You may need to contact Glacier Bay for...

I quit shipping toilets ten years ago for that reason. 20% of the shipments were broken in some way. Good luck. You could be in the 80% on...

Some people perch at the end of an elongated bowl, rather than sitting back. The sitting position between round and elongated should be the same....

If the 3" line is used as a vent for the downstairs bath, then no waste can be put down it. You must determine if that is "really" a future waste...

If size was going to be an issue, then that should have been discussed before the purchase. That water has already passed over the dam. And if you...

Right. No inspector would allow a washer in any wet vent situation. That washer would suck the trap so fast it wouldn't be funny.

Thanks Don. I'm hoping that this is a good weekend for all the fathers out there. Being one sure changed my life. I remember seeing my first...

That Kohler faucet has a vacuum breaker on it. 2

You may get by with a decorative support elsewhere under the tub to take the weight off. Like hj mentions, there is no welding of cast. It's kind...

Here is a part for the PF/2 http://www.fdsupply.com/item/pf2302/

I've seen two typs of faucets for the stand alone bidets. Does this one outlet below the rim then? The second style has a faucet that is on the top,...

2nd floor? You need to pull the bowl and reset with new wax. It has nothing to do with the main line for the second floor. Sewage would be...

Normally the tank bolts come with four washers and four nuts, plus the two rubber washers for inside the tank. We bolt the bolts to the tank first,...

Like Tom said. A good Studor Vent and shutoffs for the PEX and you up and running. Not being on site, anything else is just a guess.

I can't tell from that photo what fitting you have. A double fixture fitting will fairly well, a double santee isn't so good. Better is to have...

Some round bowls will give you 27.5" from wall to end of bowl on a standard 12" rough in. CST743E TOTO Drake round front. It's easy enough to...

The Kohler Cimarron will be much, much better than the old Mansfield Alto toilet you removed. We remove Mansfield all the time. Consumer Reports is...

Two low flow toilets and a lav are fine on a 1/2" line. ...

I would look underneath to make sure that the supplies aren't catching on anything.

The one on the left I do, the two on the right I don't. I would rather use Studor or AAV venting than the two on the right. Have you shown your...

Many of the newer furnaces need a condensate drain, as do many tankless water heaters. You may be able to drain those either at the sink or the...

In all my years of plumbing, I've never done it the other two ways. On the West Coast, they would laugh. Here, we expect every fixture to be...

Mine had all of the proper drains and vents. If you would like to see a wet vented version, it looks like this. You could easily add a wye...

You mean like this? You can use 3" on your waste stack. And yes, the upper floor needs to connect below the bottom floor or you will suck...