johnjh2o1
Plumbing Contractor for 49 years

If you switch to PVC, then use a shield coupling between the two materials. I would not glue them.

Normally you would have a vent between the p-trap and where it enters a waste line for other fixtures to prevent siphoning of the p-trap. Also, the...

Gerber also makes a wall hung toilet. We do a lot of Glenwall installs too.

I have never looked into a wall to see if a shower arm was leaking. Either put tape on the threads, or pipe dope, thread the head onto the arm by...

With 11.5" to the wall you're fine with either the 500 or the Vespin II with their standard 12" kits.

I've installed the Neorest 500 at 11.5" from the back wall. Are you measuring the wall? Or the floor mold? You can also fudge the adaper...

That works with the 2" veritcal pipe on the vent.

It is going to get better, you will see, you got to believe... You mentioned glasses, which made me think of something, and as I sit here, I got to...

It's just a matter of picking up a roof flashing, and putting the holes in the right location to drop a pipe through. It's not a lot in parts. In...

It drives the plumbing inspectors nuts that Home Depot sells product that doesn't meet plumbing codes. You may need to contact Glacier Bay for...

I quit shipping toilets ten years ago for that reason. 20% of the shipments were broken in some way. Good luck. You could be in the 80% on...

Some people perch at the end of an elongated bowl, rather than sitting back. The sitting position between round and elongated should be the same....

If the 3" line is used as a vent for the downstairs bath, then no waste can be put down it. You must determine if that is "really" a future waste...

When your priming the pump your not getting any water into the pump. The check valve needs to be closer to the well with the priming tee between the...

If size was going to be an issue, then that should have been discussed before the purchase. That water has already passed over the dam. And if you...

Right. No inspector would allow a washer in any wet vent situation. That washer would suck the trap so fast it wouldn't be funny.

Thanks Don. I'm hoping that this is a good weekend for all the fathers out there. Being one sure changed my life. I remember seeing my first...

That Kohler faucet has a vacuum breaker on it. 2

You may get by with a decorative support elsewhere under the tub to take the weight off. Like hj mentions, there is no welding of cast. It's kind...

Replace the lead line back to the cast iron. John

Here is a part for the PF/2 http://www.fdsupply.com/item/pf2302/

I've seen two typs of faucets for the stand alone bidets. Does this one outlet below the rim then? The second style has a faucet that is on the top,...

2nd floor? You need to pull the bowl and reset with new wax. It has nothing to do with the main line for the second floor. Sewage would be...

Normally the tank bolts come with four washers and four nuts, plus the two rubber washers for inside the tank. We bolt the bolts to the tank first,...

Like Tom said. A good Studor Vent and shutoffs for the PEX and you up and running. Not being on site, anything else is just a guess.

Delta, Kohler has a habit of changing their design very often making hard to find the correct parts for repair. Delta's parts are available just...

I can't tell from that photo what fitting you have. A double fixture fitting will fairly well, a double santee isn't so good. Better is to have...

Some round bowls will give you 27.5" from wall to end of bowl on a standard 12" rough in. CST743E TOTO Drake round front. It's easy enough to...

The Kohler Cimarron will be much, much better than the old Mansfield Alto toilet you removed. We remove Mansfield all the time. Consumer Reports is...

Two low flow toilets and a lav are fine on a 1/2" line. ...