View Profile: rshackleford - Terry Love Plumbing & Remodel DIY Forum & Blog

Today, 02:05 PM

Terry replied to a thread Please help make heads or tails of my bathroom rough in in Plumbing Forum Discussion & Blog

Pipe B is in the wall. A lav that wet vents the toilet. Pipe A is 13" in front of the framed wall. This is for a standard 12" rough toilet. Pipe...

1 replies | 13 view(s)

Yesterday, 10:43 PM

Terry replied to a thread Shim toilet in front and back? in Toilet Forum discussions

Any bowl needs to set flat to the floor without rocking. Shim as needed, though we tend to shim the back and try to pin the front of the bowl to the...

3 replies | 61 view(s)

Yesterday, 10:36 PM

Terry replied to a thread Gator bite and tub shower problems in Plumbing Forum Discussion & Blog

If there is "any" restriction on the tub spout piping, it will force water up to the shower head. It needs to be unrestricted copper, galvanized or...

3 replies | 64 view(s)

Yesterday, 10:34 PM

Terry replied to a thread Help Replacing 1" Main Water Shut Off Valve in Plumbing Forum Discussion & Blog

I would remove the PRV first, and then you will be able to unsolder the shutoff valve and resolder a new one. While you are at it, you might also...

9 replies | 130 view(s)

Yesterday, 12:42 PM

Terry replied to a thread Toto Drake II vs Aquia - Ostomy bag in Toilet Forum discussions

You can dump them in a container, but it's easier with an elongated bowl to just do it all there while sitting. Plus, you can't take all that other...

6 replies | 189 view(s)

Yesterday, 10:38 AM

Terry started a thread Installing a new Moen Posi-Temp shower valve in Shower & bathtub Forum & Blog

Sometimes it's time to replace an old shower faucet and go with a new pressure balanced faucet. Moen makes the Posi-Temp, which holds the...

1 replies | 33 view(s)

Yesterday, 10:18 AM

Terry replied to a thread Drake ii Rough-in vs. existing 15 5/8” in Toilet Forum discussions

You would be looking at the Vespin II if you wanted to go with the 14" Unift adapter. Same tank, but a different bowl that allows moving it back 2"....

2 replies | 44 view(s)

Yesterday, 09:40 AM

Terry replied to a thread Kohler shower hardware.... in Plumbing Forum Discussion & Blog

Looking at the spec sheets everything looks fine. 1/2 NPT, which is standard stuff. I see that the K-9511 has two outlets, a male 1/2" pipe...

3 replies | 67 view(s)

Yesterday, 09:19 AM

Terry replied to a thread Base Cabinet drain re-route in Plumbing Forum Discussion & Blog

The plumbing takes presidence over trash bins. That's why you have a plumbing inspector, and plumbing permits.

7 replies | 125 view(s)

05-19-2013, 10:11 PM

Terry replied to a thread Problem with hose bib in Plumbing Forum Discussion & Blog

Normally we would do it from an inside wall to access the connection to an outside hosebib.

1 replies | 68 view(s)

05-19-2013, 07:57 PM

Terry replied to a thread Redoing Plumbing in Old House - Manifold and Tee Question in Plumbing Forum Discussion & Blog

It doesn't really matter whether the manifold is before or after the 3/4" upstairs pipes as long as it's sized properly. Water pipe sizing

8 replies | 155 view(s)

05-19-2013, 07:20 PM

Terry replied to a thread In looking at the Toilet's - will the Drake II 1G fit a 1.28 flapper in Toilet Forum discussions

Next It looks like you would have to change out quite a bit. The parts for the Drake II 1G ST453U are quite different than for the ST454E...

6 replies | 132 view(s)

05-19-2013, 10:23 AM

Terry replied to a thread Septic smells - Cadet 3 in Toilet Forum discussions

If may have need two wax rings if the flange was too low. http://www.americanstandard-us.com/assets/documents/amstd/install/Install_2826.pdf ...

1 replies | 60 view(s)

05-18-2013, 07:46 PM

Terry replied to a thread Power vent or power direct vent recommendations in Water Heater Forum, Tanks

I like the Rheem units too. You might also look into tankless if you have a good enough gas supply there.

10 replies | 195 view(s)

05-18-2013, 07:37 PM

Terry replied to a thread Refridgerator suppy valve in Remodel Forum & Blog

It may be easiest to work out from the CPVC I would cut it back and start over. The threads where the shutoff threads down look to be fine...

10 replies | 131 view(s)

05-18-2013, 07:17 PM

Terry replied to a thread Toto Drake II vs Aquia - Ostomy bag in Toilet Forum discussions

I had the TOTO Aquia for a while, and then changed it for a TOTO Double Cyclone. The Aquia was pre Ostomy bag, and the double cyclone was during...

6 replies | 189 view(s)

05-18-2013, 11:55 AM

Terry replied to a thread Unifit on home owner remodel in Toilet Forum discussions

In an old 1939 home I have not had an inspector make me change that dimension. Some old homes in Seattle are 7 feet for the bath. That meant 24"...

2 replies | 72 view(s)

05-18-2013, 11:13 AM

Terry replied to a thread Moen tub/ shower control, uneven pressure in Plumbing Forum Discussion & Blog

A thirty year old non-balanced Moen, the cartridge would not have much affect on water pressure side to side. If you have the pressure balanced...

3 replies | 63 view(s)

05-18-2013, 11:09 AM

Terry replied to a thread Kitchen sink backing up when washing machine drains in Plumbing Forum Discussion & Blog

The previous drawing you have posted shows many more fixtures. A standard laundry trap drain is pretty small. Some people are installing...

9 replies | 28528 view(s)

05-18-2013, 11:04 AM

Terry replied to a thread Is this ok... stand pipe, laundry tub, bar sink, shower plumbing in Plumbing Forum Discussion & Blog

When the fixture above drains quickly, like pulling the plug and draining, it can siphon the trap below. Will the bar sink drain slow enough?...

6 replies | 131 view(s)

05-18-2013, 10:52 AM

Terry replied to a thread Is this ok... stand pipe, laundry tub, bar sink, shower plumbing in Plumbing Forum Discussion & Blog

And they do reject it when inspected. But this guy is just up the road from me, and maybe in BC it's okay. I don't like doing things twice, so I...

6 replies | 131 view(s)

05-18-2013, 10:23 AM

Terry replied to a thread Help with changing Price Phister knob to Moen lever tub handle in Shower & bathtub Forum & Blog

I believe you have a Price Phister cartridge there. It's not a Moen cartridge in the wall. Price Phister Avante valve You need something...

3 replies | 81 view(s)

05-17-2013, 05:56 PM

Terry replied to a thread Kitchen sink backing up when washing machine drains in Plumbing Forum Discussion & Blog

In the UPC code, they don't allow a laundry tray to wet vent over a washer. They only allow wet venting on bathroom fixtures. Which a laundry...

9 replies | 28528 view(s)

05-17-2013, 02:46 PM

Terry replied to a thread Connection of Water Intake Pipes to Shower Valve in Shower & bathtub Forum & Blog

Whatever it takes. You can run the pipe in circles if needed. They're saying "In a perfect world." it would be nice to have them with that...

4 replies | 97 view(s)

05-17-2013, 11:02 AM

Terry replied to a thread No cold water in shower in Shower & bathtub Forum & Blog

No cold? You may have a thermostatic valve there, and it may just be giving you a tight range. Sometimes you can remove the valve and reinstall...

5 replies | 98 view(s)

05-17-2013, 10:50 AM

Terry replied to a thread What caulk to use to seal water pipe through basement wall in Plumbing Forum Discussion & Blog

I would be thinking 100% Silicone on that. Too bad it can't be sealed from the outside. Water pushing up against the foundation is hard to seal. ...

3 replies | 122 view(s)

05-17-2013, 08:41 AM

Terry replied to a thread Why do plumbing jobs always leak in Plumbing Forum Discussion & Blog

I would think so. Having a leak after a repair? How would anyone stay in business? Any good service plumber will be dependable. When I was...

4 replies | 138 view(s)

05-16-2013, 06:22 PM

Terry replied to a thread depth of the rough-in valve in Plumbing Forum Discussion & Blog

It depends on the valve. Some of the Home Depot stuff years ago had a tollerence of 1/8" Something like Moen may have 3/4", and if they are...

5 replies | 144 view(s)

05-16-2013, 05:34 PM

Terry replied to a thread Remodeled Kitchen Sink Plumbing in Plumbing Forum Discussion & Blog

You may want to open the wall and see what can be changed there. If there is any way to lower the drain, or if not, get a shallower sink. First...

6 replies | 190 view(s)

05-16-2013, 05:28 PM

Terry replied to a thread New electric water heater on concrete slab in Plumbing Forum Discussion & Blog

Since the advent of check valved water meters we are doing more and more expansion tanks on our water heater installs. Some parts of Seattle have...

21 replies | 369 view(s)

rshackleford
DIY Senior Member

Mini Statistics

More 1 Friend

Terry

Recent Visitors

Basic Information

About rshackleford

Signature

Contact

Statistics

Total Posts

General Information

1 Friend

Terry

rshackleford DIY Senior Member

Mini Statistics

More 1 Friend

Terry

Recent Visitors

Basic Information

About rshackleford

Signature

Contact

Statistics

Total Posts

General Information

1 Friend

Terry

rshackleford
DIY Senior Member