Search results

I have another toilet that is installed the same way this one will be. The toilet goes directly into a 3" line, the pipe from the toilet doesn't have a vent on it, but the 3" main does have a 2" line that is a lav drain/wet-vent about 2' from where the toilet connects. I guess I better call...

Well, no pics because its still under concrete, but, the 2" vent comes off the 3" pipe (before the toilet) with a wye fitting that is 45 degrees from horizontal then a 45 straight up the wall eventually going to the roof. Not a wet vent. I believe it will work and is to code in PA.

Thanks Terry. Yes, the vent is between the shower and the toilet. The 3" line dumps into the 4" main that goes directly to the septic tank so no fixtures after the toilet.

Hello, getting ready to install a toilet in my basement. House is only 4 years old and I placed drains in floor when building but now we have decided to move location of the toilet in the basement. Luckily it will still be directly above the 3" PVC under the slab and there is a properly...

If they damaged something, they should definitely pay. If something came loose because of the hammering, then you will likely have to pay since it would have eventually came loose anyway.

Wire in Romex is solid, THHN is stranded, much easier to pull the THHN. The insulation is single layered on the wires in Romex, THHN is much tougher. Compare the two at your local store, you'll see the difference. The insulation on the wires in Romex are damaged much easier when you pull...

My issue is that he implied that I am lying about talking to my local code inspectors.

Yep I'm a liar. Sorry for asking questions on this forum. Guess that isn't what this is for, right? From now on I will direct all questions to the local inspector and ignore pricks like you. Anyway, here is what PA code uses: Building Codes Search Printable Version Text-Only...

This isn't the first house I have built, but it is the first one with the codes, (in Pennsylvania). I used to be an electrician, so the fundamentals haven't changed, just some of the requirements, like AFCI's. Couldn't buy them around here when I was an electrician. I have been in constant...

Shouldn't hurt the copper much, you could wrap it with duct tape or something, similar, just where you won't see it. FYI, aluminum does react with concrete over time.

What exactly was mandated, AFCI's on bedroom receptacles only? Any other places AFCI's are mandated? I am framing my new house currently and will be wiring soon, so this info will be handy. Thanks, Mark

Another question, do AFCI's have to be used for lighting cicuits in bedrooms or just mandatory for outlets? Thanks, Mark

You first need to determine how many other fixtures are on the circuit. This can be done by turning on all the lights and turning off the breaker for that one kitchen light. See what else turns off. You should also check all outlets in that area. Many times, folks will put lights on with...

UV exposure Is there a window in the attic, or some other opening, that allows light from outside to hit the pex tubing in the attic? As far as I know, all pex tubing must be protected from UV light.

Dual bibs? I would like to have hot and cold to the outside. Which dual frostfree bibs are high quality? Thanks.

They are 95 to 100 watts per bulb or .79 to .83 amps per bulb, assuming 120 volts. Therefore, with 5 fixtures, I will have 1000 watts of light, nice and bright. I will have seperate switches for them, 1 for the bench, one for lights above cars, one for lights in front of cars. It is worth it...

Garage lights I would recommend 4 or 8 foot flourescent fixtures in the garage. There never seems to be enough light when you want to work on something. I am building a new house with a 28x32 garage right now. I plan on installing five two tube 8' fixtures in the garage. One length-wise...

More questions, variable speed injection, mixing valves.... Hello again. I will be using a properly sized condensing boiler with an indirect hot water tank. Now my issue involves the different temperature requirements of two different radiant applications. In a house I built 9 years ago, I...

Hello, I am currently building a new house. Ranch style, 1650 sq ft, radiant floor heat in basement and main floor. I plan to at least install the duct work for central A/C while I am roughing the house in, get it under the insulation in the attic. I am looking for suggestions on what type of...

Vent pipe copper? Is that a piece of 4" copper for the main stack? If so, remove it, sell it, and pay for everything you need for your upgrades!